喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有,,請放心下載,,文件全都包含在內,,【有疑問咨詢QQ:414951605 或 1304139763】
==========================================喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有,,請放心下載,,文件全都包含在內,,【有疑問咨詢QQ:414951605 或 1304139763】
==========================================
畢業設計(論文)外文翻譯
如何延長軸承壽命
摘要: 自然界苛刻的工作條件會導致軸承的失效,但是如果遵循一些簡單的規則,軸承正常運轉的機會是能夠被提高的。在軸承的使用過程當中,過分的忽視會導致軸承的過熱現象,也可能使軸承不能夠再被使用,甚至完全的破壞。但是一個被損壞的軸承,會留下它為什么被損壞的線索。通過一些細致的偵察工作,我們可以采取行動來避免軸承的再次失效。
關鍵詞: 軸承 失效 壽命
導致軸承失效的原因很多,但常見的是不正確的使用、污染、潤滑劑使用不當、裝卸或搬運時的損傷及安裝誤差等。診斷失效的原因并不困難,因?yàn)楦鶕?jù)軸承上留下的痕跡可以確定軸承失效的原因。
然而,當事后的調查分析提供出寶貴的信息時,最好首先通過正確地選定軸承來完全避免失效的發生。為了做到這一點,再考察一下制造廠商的尺寸定位指南和所選軸承的使用特點是非常重要的。
1 軸承失效的原因
在球軸承的失效中約有40%是由灰塵、臟物、碎屑的污染以及腐蝕造成的。污染通常是由不正確的使用和不良的使用環境造成的,它還會引起扭矩和噪聲的問題。由環境和污染所產生的軸承失效是可以預防的,而且通過簡單的肉眼觀察是可以確定產生這類失效的原因。
通過失效后的分析可以得知對已經失效的或?qū)⒁У妮S承應該在哪些方面進行查看。弄清諸如剝蝕和疲勞破壞一類失效的機理,有助于消除問題的根源。
只要使用和安裝合理,軸承的剝蝕是容易避免的。剝蝕的特征是在軸承圈滾道上留有由沖擊載荷或不正確的安裝產生的壓痕。剝蝕通常是在載荷超過材料屈服極限時發生的。如果安裝不正確從而使某一載荷橫穿軸承圈也會產生剝蝕。軸承圈上的壓坑還會產生噪聲、振動和附加扭矩。
類似的一種缺陷是當軸承不旋轉時由于滾珠在軸承圈間振動而產生的橢圓形壓痕。這種破壞稱為低荷振蝕。這種破壞在運輸中的設備和不工作時仍振動的設備中都會產生。此外,低荷振蝕產生的碎屑的作用就象磨粒一樣,會進一步損害軸承。與剝蝕不同,低荷振蝕的特征通常是由于微振磨損腐蝕在潤滑劑中會產生淡紅色。
消除振動源并保持良好的軸承潤滑可以防止低荷振蝕。給設備加隔離墊或?qū)Φ鬃M(jìn)行隔離可以減輕環境的振動。另外在軸承上加一個較小的預載荷不僅有助于滾珠和軸承圈保持緊密的接觸,并且對防止在設備運輸中產生的低荷振蝕也有幫助。
造成軸承卡住的原因是缺少內隙、潤滑不當和載荷過大。在卡住之前,過大的摩擦和熱量使軸承鋼軟化。過熱的軸承通常會改變顏色,一般會變成藍黑色或淡黃色。摩擦還會使保持架受力,這會破壞支承架,并加速軸承的失效。
材料過早出現疲勞破壞是由重載后過大的預載引起的。如果這些條件不可避免,就應仔細計算軸承壽命,以制定一個維護計劃。
另一個解決辦法是更換材料。若標準的軸承材料不能保證足夠的軸承壽命,就應當采用特殊的材料。另外,如果這個問題是由于載荷過大造成的,就應該采用抗載能力更強或其他結構的軸承。
蠕動不象過早疲勞那樣普遍。軸承的蠕動是由于軸和內圈之間的間隙過大造成的。蠕動的害處很大,它不僅損害軸承,也破壞其他零件。
蠕動的明顯特征是劃痕、擦痕或軸與內圈的顏色變化。為了防止蠕動,應該先用肉眼檢查一下軸承箱件和軸的配件。
蠕動與安裝不正有關。如果軸承圈不正或翹起,滾珠將沿著一個非圓周軌道運動。這個問題是由于安裝不正確或公差不正確或軸承安裝現場的垂直度不夠造成的。如果偏斜超過0.25°,軸承就會過早地失效。
檢查潤滑劑的污染比檢查裝配不正或蠕動要困難得多。污染的特征是使軸承過早的出現磨損。潤滑劑中的固體雜質就象磨粒一樣。如果滾珠和保持架之間潤滑不良也會磨損并削弱保持架。在這種情況下,潤滑對于完全加工形式的保持架來說是至關重要的。相比之下,帶狀或冠狀保持架能較容易地使?jié)櫥瑒┑竭_(dá)全部表面。
銹是濕氣污染的一種形式,它的出現常常表明材料選擇不當。如果某一材料經檢驗適合工作要求,那么防止生銹的最簡單的方法是給軸承包裝起來,直到安裝使用時才打開包裝。
2 避免失效的方法
解決軸承失效問題的最好辦法就是避免失效發生。這可以在選用過程中通過考慮關鍵性能特征來實現。這些特征包括噪聲、起動和運轉扭矩、剛性、非重復性振擺以及徑向和軸向間隙。
扭矩要求是由潤滑劑、保持架、軸承圈質量(彎曲部分的圓度和表面加工質量)以及是否使用密封或遮護裝置來決定。潤滑劑的粘度必須認真加以選擇,因?yàn)椴贿m宜的潤滑劑會產生過大的扭矩,這在小型軸承中尤其如此。另外,不同的潤滑劑的噪聲特性也不一樣。舉例來說,潤滑脂產生的噪聲比潤滑油大一些。因此,要根據不同的用途來選用潤滑劑。
在軸承轉動過程中,如果內圈和外圈之間存在一個隨機的偏心距,就會產生與凸輪運動非常相似的非重復性振擺(NRR)。保持架的尺寸誤差和軸承圈與滾珠的偏心都會引起NRR。和重復性振擺不同的是,NRR是沒有辦法進行補償?shù)摹?
在工業中一般是根據具體的應用來選擇不同類型和精度等級的軸承。例如,當要求振擺最小時,軸承的非重復性振擺不能超過0.3微米。同樣,機床主軸只能容許最小的振擺,以保證切削精度。因此在機床的應用中應該使用非重復性振擺較小的軸承。
在許多工業產品中,污染是不可避免的,因此常用密封或遮護裝置來保護軸承,使其免受灰塵或臟物的侵蝕。但是,由于軸承內外圈的運動,使軸承的密封不可能達到完美的程度,因此潤滑油的泄漏和污染始終是一個未能解決的問題。
一旦軸承受到污染,潤滑劑就要變質,運行噪聲也隨之變大。如果軸承過熱,它將會卡住。當污染物處于滾珠和軸承圈之間時,其作用和金屬表面之間的磨粒一樣,會使軸承磨損。采用密封和遮護裝置來?yè)蹰_臟物是控制污染的一種方法。
噪聲是反映軸承質量的一個指標。軸承的性能可以用不同的噪聲等級來表示。
噪聲的分析是用安德遜計進行的,該儀器在軸承生產中可用來控制質量,也可對失效的軸承進行分析。將一傳感器連接在軸承外圈上,而內圈在心軸以1800r/min的轉速旋轉。測量噪聲的單位為anderon。即用um/rad表示的軸承位移。
根據經驗,觀察者可以根據聲音辨別出微小的缺陷。例如,灰塵產生的是不規則的劈啪聲;滾珠劃痕產生一種連續的爆破聲,確定這種劃痕最困難;內圈損傷通常產生連續的高頻噪聲,而外圈損傷則產生一種間歇的聲音。
軸承缺陷可以通過其頻率特性進一步加以鑒定。通常軸承缺陷被分為低、中、高三個波段。缺陷還可以根據軸承每轉動一周出現的不規則變化的次數加以鑒定。
低頻噪聲是長波段不規則變化的結果。軸承每轉一周這種不規則變化可出現1.6~10次,它們是由各種干涉(例如 軸承圈滾道上的凹坑)引起的??刹煊X的凹坑是一種制造缺陷,它是在制造過程中由于多爪卡盤夾的太緊而形成的。
中頻噪聲的特征是軸承每旋轉一周不規則變化出現10~60次。這種缺陷是由在軸承圈和滾珠的磨削加工中出現的振動引起的。軸承每旋轉一周高頻不規則變化出現60~300次,它表明軸承上存在著密集的振痕或大面積的粗糙不平。
利用軸承的噪聲特性對軸承進行分類,用戶除了可以確定大多數廠商所使用的ABEC標準外,還可確定軸承的噪聲等級。ABEC標準只定義了諸如孔、外徑、振擺等尺寸公差。隨著ABEC級別的增加(從3增到9),公差逐漸變小。但ABEC等級并不能反映其他軸承特性,如軸承圈質量、粗糙度、噪聲等。因此,噪聲等級的劃分有助于工業標準的改進。
附錄:畢業設計(論文)外文翻譯原文
EXTENDING BEARING LIFE
Abstract:Nature works hard to destroy bearings, but their chances of survival can be improved by following a few simple guidelines. Extreme neglect in a bearing leads to overheating and possibly seizure or, at worst, an explosion. But even a failed bearing leaves clues as to what went wrong. After a little detective work, action can be taken to avoid a repeat performance.
Keywords: bearings failures life
Bearings fail for a number of reasons,but the most common are misapplication,contamination,improper lubricant,shipping or handling damage,and misalignment. The problem is often not difficult to diagnose because a failed bearing usually leaves telltale signs about what went wrong.
However,while a postmortem yields good information,it is better to avoid the process altogether by specifying the bearing correctly in The first place.To do this,it is useful to review the manufacturers sizing guidelines and operating characteristics for the selected bearing.
Equally critical is a study of requirements for noise, torque, and runout, as well as possible exposure to contaminants, hostile liquids, and temperature extremes. This can provide further clues as to whether a bearing is right for a job.
1 Why bearings fail
About 40% of ball bearing failures are caused by contamination from dust, dirt, shavings, and corrosion. Contamination also causes torque and noise problems, and is often the result of improper handling or the application environment.Fortunately, a bearing failure caused by environment or handling contamination is preventable,and a simple visual examination can easily identify the cause.
Conducting a postmortem il1ustrates what to look for on a failed or failing bearing.Then,understanding the mechanism behind the failure, such as brinelling or fatigue, helps eliminate the source of the problem.
Brinelling is one type of bearing failure easily avoided by proper handing and assembly. It is characterized by indentations in the bearing raceway caused by shock loading-such as when a bearing is dropped-or incorrect assembly. Brinelling usually occurs when loads exceed the material yield point(350,000 psi in SAE 52100 chrome steel).It may also be caused by improper assembly, Which places a load across the races.Raceway dents also produce noise,vibration,and increased torque.
A similar defect is a pattern of elliptical dents caused by balls vibrating between raceways while the bearing is not turning.This problem is called false brinelling. It occurs on equipment in transit or that vibrates when not in operation. In addition, debris created by false brinelling acts like an abrasive, further contaminating the bearing. Unlike brinelling, false binelling is often indicated by a reddish color from fretting corrosion in the lubricant.
False brinelling is prevented by eliminating vibration sources and keeping the bearing well lubricated. Isolation pads on the equipment or a separate foundation may be required to reduce environmental vibration. Also a light preload on the bearing helps keep the balls and raceway in tight contact. Preloading also helps prevent false brinelling during transit.
Seizures can be caused by a lack of internal clearance, improper lubrication, or excessive loading. Before seizing, excessive, friction and heat softens the bearing steel. Overheated bearings often change color,usually to blue-black or straw colored.Friction also causes stress in the retainer,which can break and hasten bearing failure.
Premature material fatigue is caused by a high load or excessive preload.When these conditions are unavoidable,bearing life should be carefully calculated so that a maintenance scheme can be worked out.
Another solution for fighting premature fatigue is changing material.When standard bearing materials,such as 440C or SAE 52100,do not guarantee sufficient life,specialty materials can be recommended. In addition,when the problem is traced back to excessive loading,a higher capacity bearing or different configuration may be used.
Creep is less common than premature fatigue.In bearings.it is caused by excessive clearance between bore and shaft that allows the bore to rotate on the shaft.Creep can be expensive because it causes damage to other components in addition to the bearing.
0ther more likely creep indicators are scratches,scuff marks,or discoloration to shaft and bore.To prevent creep damage,the bearing housing and shaft fittings should be visually checked.
Misalignment is related to creep in that it is mounting related.If races are misaligned or cocked.The balls track in a noncircumferencial path.The problem is incorrect mounting or tolerancing,or insufficient squareness of the bearing mounting site.Misalignment of more than 1/4?can cause an early failure.
Contaminated lubricant is often more difficult to detect than misalignment or creep.Contamination shows as premature wear.Solid contaminants become an abrasive in the lubricant.In addition。insufficient lubrication between ball and retainer wears and weakens the retainer.In this situation,lubrication is critical if the retainer is a fully machined type.Ribbon or crown retainers,in contrast,allow lubricants to more easily reach all surfaces.
Rust is a form of moisture contamination and often indicates the wrong material for the application.If the material checks out for the job,the easiest way to prevent rust is to keep bearings in their packaging,until just before installation.
2 Avoiding failures
The best way to handle bearing failures is to avoid them.This can be done in the selection process by recognizing critical performance characteristics.These include noise,starting and running torque,stiffness,nonrepetitive runout,and radial and axial play.In some applications, these items are so critical that specifying an ABEC level alone is not sufficient.
Torque requirements are determined by the lubricant,retainer,raceway quality(roundness cross curvature and surface finish),and whether seals or shields are used.Lubricant viscosity must be selected carefully because inappropriate lubricant,especially in miniature bearings,causes excessive torque.Also,different lubricants have varying noise characteristics that should be matched to the application. For example,greases produce more noise than oil.
Nonrepetitive runout(NRR)occurs during rotation as a random eccentricity between the inner and outer races,much like a cam action.NRR can be caused by retainer tolerance or eccentricities of the raceways and balls.Unlike repetitive runout, no compensation can be made for NRR.
NRR is reflected in the cost of the bearing.It is common in the industry to provide different bearing types and grades for specific applications.For example,a bearing with an NRR of less than 0.3um is used when minimal runout is needed,such as in disk—drive spindle motors.Similarly,machine—tool spindles tolerate only minimal deflections to maintain precision cuts.Consequently, bearings are manufactured with low NRR just for machine-tool applications.
Contamination is unavoidable in many industrial products,and shields and seals are commonly used to protect bearings from dust and dirt.However,a perfect bearing seal is not possible because of the movement between inner and outer races.Consequently,lubrication migration and contamination are always problems.
Once a bearing is contaminated, its lubricant deteriorates and operation becomes noisier.If it overheats,the bearing can seize.At the very least,contamination causes wear as it works between balls and the raceway,becoming imbedded in the races and acting as an abrasive between metal surfaces.Fending off dirt with seals and shields illustrates some methods for controlling contamination.
Noise is as an indicator of bearing quality.Various noise grades have been developed to classify bearing performance capabilities.
Noise analysis is done with an Anderonmeter, which is used for quality control in bearing production and also when failed bearings are returned for analysis. A transducer is attached to the outer ring and the inner race is turned at 1,800rpm on an air spindle. Noise is measured in andirons, which represent ball displacement in μm/rad.
With experience, inspectors can identify the smallest flaw from their sound. Dust, for example, makes an irregular crackling. Ball scratches make a consistent popping and are the most difficult to identify. Inner-race damage is normally a constant high-pitched noise, while a damaged outer race makes an intermittent sound as it rotates.
Bearing defects are further identified by their frequencies. Generally, defects are separated into low, medium, and high wavelengths. Defects are also referenced to the number of irregularities per revolution.
Low-band noise is the effect of long-wavelength irregularities that occur about 1.6 to 10 times per revolution. These are caused by a variety of inconsistencies, such as pockets in the race. Detectable pockets are manufacturing flaws and result when the race is mounted too tightly in multiplejaw chucks.
Medium-hand noise is characterized by irregularities that occur 10 to 60 times per revolution. It is caused by vibration in the grinding operation that produces balls and raceways. High-hand irregularities occur at 60 to 300 times per revolution and indicate closely spaced chatter marks or widely spaced, rough irregularities.
Classifying bearings by their noise characteristics allows users to specify a noise grade in addition to the ABEC standards used by most manufacturers. ABEC defines physical tolerances such as bore, outer diameter, and runout. As the ABEC class number increase (from 3 to 9), tolerances are tightened. ABEC class, however, does not specify other bearing characteristics such as raceway quality, finish, or noise. Hence, a noise classification helps improve on the industry standard.
湘潭大學興湘學院
畢業設計說明書
題 目:小功率機械無級變速器結構設計
專 業: 機械設計及其自動化
學 號: 2007964210
姓 名: 龍 雄
指導教師: 聶松輝 (教授)
完成日期: 2011年5月
湘潭大學興湘學院
畢業論文(設計)任務書
論文(設計)題目: 小功率機械無級變速器結構設計
學號: 2007964210 姓名: 龍雄 專業: 機械設計制造及其自動化
指導教師: 聶 松 輝 系主任: 周 友 行
一、主要內容及基本要求
1、設計一種小功率機械無級變速器,要求以鋼球?yàn)橹虚g元件;
2、輸入功率P=1.1kw,輸入轉速n=1500rpm,調速范圍R=9;
3、一張裝配圖A0#1張,零件圖總量A0#1張;
4、設計說明書一份;
5、英文文獻一份。
二、重點研究的問題
1、小功率機械無級變速器原理及其結構;
2、變速原理的傳動結構的實現。
三、進度安排
序號
各階段完成的內容
完成時間
1
熟悉課題及基礎資料
第一周
2
調研及收集資料
第二周
3
方案設計與討論
第三~四周
4
無級變速器布局設計
第五周
5
無級變速器總裝配圖設計
第六~九周
6
無級變速器零件圖設計
第十周
7
撰寫說明書
第十一周
8
英文文獻翻譯,答辯
第十二周
四、應收集的資料及主要參考文獻
[1] 阮忠唐. 機械無級變速器[M]. 機械工業出版社.
[2] 阮忠唐.機械無級變速器設計與選用指南[M].化學工業出版社.
[3] 徐灝.機械設計手冊第3卷[M].機械工業出版社.
[4] 毛謙德.袖珍機械設計師手冊第3版[M].機械工業出版社.
[5] 機械設計手冊新版第2卷[M].機械工業出版社.
湘 潭 大 學
畢業論文(設計)評閱表
學號2007964210 姓名 龍雄 專業 機械設計制造及其自動化
畢業論文(設計)題目: 小功率機械無級變速器結構設計
評價項目
評 價 內 容
選題
1.是否符合培養目標,體現學科、專業特點和教學計劃的基本要求,達到綜合訓練的目的;
2.難度、份量是否適當;
3.是否與生產、科研、社會等實際相結合。
能力
1.是否有查閱文獻、綜合歸納資料的能力;
2.是否有綜合運用知識的能力;
3.是否具備研究方案的設計能力、研究方法和手段的運用能力;
4.是否具備一定的外文與計算機應用能力;
5.工科是否有經濟分析能力。
論文
(設計)質量
1.立論是否正確,論述是否充分,結構是否嚴謹合理;實驗是否正確,設計、計算、分析處理是否科學;技術用語是否準確,符號是否統一,圖表圖紙是否完備、整潔、正確,引文是否規范;
2.文字是否通順,有無觀點提煉,綜合概括能力如何;
3.有無理論價值或?qū)嶋H應用價值,有無創新之處。
綜
合
評
價
評閱人:
2009年 月 日
湘潭大學興湘學院
畢業論文(設計)鑒定意見
學號:2007964210 姓名: 龍雄 專業: 機械設計制造及其自動化
畢業論文(設計說明書) 34 頁 圖 表 6 張
論文(設計)題目:小功率機械無級變速器結構設計
內容提要:小功率機械無級變速器結構設計
機械無級變速器是一種能適應工藝要求多變、工藝流程機械化和自動化發展以
及改善機械工作性能的一種通用傳動裝置。本文簡要介紹了摩擦式機械無級變
速器的基本結構、設計計算的方法、材質及潤滑等方面的知識,并以此作為本
次無級變速器設計的理論基礎。
本設計采用的是以鋼球錐輪作為中間傳動元件,通過改變鋼球的工作半徑來實
現輸出軸轉速連續變化的鋼球錐輪式無級變速器。本文分析了在傳動過程中變
速器的主、從動輪,鋼球和外環的工作原理和受力關系;詳細推導了實用的鋼
球錐輪式無級變速設計的計算公式;并針對設計所選擇的參數進行了具體的設
計計算;繪制了所計算的球錐輪式無級變速器的裝配圖和主要傳動元件的零件
圖,將此變速器的結構和工藝等的要求表達得更為清楚。
這種無級變速器有良好的結構和性能優勢,具有很強的實用價值,完全可以作
為批量生產的無級變速器。其主要特點是:1.變速范圍較寬;2.恒功率特性好;
3.可以升、降速,正、反轉。4.運轉平穩,抗沖擊能力較強;5.輸出功率較大;
6.使用壽命長7.調速簡單,工作可靠;8.容易維修。
指導教師評語
該生有較好的基礎知識與專業知識,具有一定獨立工作的能力。有一定專業英文文獻閱讀與翻譯能力,計算機操作熟練。勞動紀律性較好,工作較認真。能如期完成畢業設計任務,圖面質量較好。
同意其參加答辯。
指導教師:
2011年 6月 3 日
答辯簡要情況及評語
答辯過程中講述條理清晰,回答問題基本正確,設計方案合理,圖面質量較好,說明書撰寫較認真。
建議成績?cè)u(píng)定為“中等”。
答辯小組組長:
2011年 6月 7 日
答辯委員會意見
同意通過答辯;
成績?cè)u(píng)定為“中等”。
答辯委員會主任:
2011年 6月 8 日