筆記本電腦卡勾的塑料注塑模具設計-抽芯注射模含7張CAD圖,筆記本電腦,塑料,注塑,模具設計,注射,cad 卡勾注塑模設計 摘要 本設計的成品為一卡勾，在設計過程中按以下步驟設計模具：卡勾注塑模工藝規程的編制—注塑模的結構設計—模具設計的有關計算—模具加熱與冷卻系統設計—模具閉合高度的確定—注塑機有關參數的校核，最后是繪制模具總裝配圖。在注塑模工藝規程的編制的過程中，要著重分析制品原材料（ABS）的各項成型工藝參數；在模具結構設計中應注意的是斜頂桿起成型兼頂出的作用；模具設計計算的要點是型腔與型芯徑向尺寸及深度方向尺寸的計算，型腔與型芯的計算在整個設計過程中顯得尤為重要，因?yàn)樗鼈冎苯雨P(guān)系到制品的尺寸精度；模具總裝圖和非標準零件圖用AutoCAD畫出，圖中需標注的各項參數如尺寸，公差，技術要求，圖紙布局等均應按國家標準設計。設計中出現的標準件如螺釘?shù)鹊牧慵D無需一一畫出，但應參照文獻查出其具體結構尺寸。 關鍵詞：卡勾，工藝規程，國家標準 卡勾注塑模設計 Abstralt The finished product originally designed is cancelled for one calorie, design the mould according to the following step in the course of designing: Card collude note mould establishment - structural design - mold design that note mould , craft of rules about calculate - mould is it close sureness of height with cooling system design - mould to heat- The check about the parameter of the moulding plastics machine, draw the total installation diagram of mould at the end. While the note moulds establishment of the craft rules , should analyse every shaping craft parameter of the products raw materials (ABS ) emphatically; Function that play shaping and concurrently carries out that the ones that should notice are an oblique mandrel in the structural design of the mould ; Main point that mold design calculate type and type core foot-path calculation of size toward size and depth, the calculation of the core with the type of of the type seems particularly important in the course of designing entirely, because they concern the precision of size of the products directly; Mould assembly is pursued to be drawn with the non-standard part picture with AutoCAD, every parameter of needing to mark in the picture is like the size, public errand , specification requirement , the overall arrangement of the drawing,etc. should be designed according to the national standard. The standard component appearing in the design does not need to draw one by one such as the part picture of screw ,etc., but should find its concrete physical dimension according to documents . Keyword: The card is cancelled , craft rules, national standard