茶杯塑件塑料注射模具設計,茶杯,塑料,注射,模具設計 洛陽理工學院畢業論文 CAD/CAM Computer technology has risen in an exponential curve. Only a generation ago computers were not really needed for NC control. Except for relatively few five-axis machines. NC was point to point, which was easily accomplished with manual programming. With the advent of two-dimensional profiling, hower, a need arose for numerous calculations to generate the curved profile. At that point the computer was looked upon as a useful tool in manufacturing engineering. After some development, it was found that punched or magnetic tape could be dispensed with entirely in favor of computer programs that controlled the machines directly. Then came the minicomputers, which when operating with the central processor brought about the first real concept of the automatic factory. All of these developments were important steps in the advance of technology. The computer is no longer viewed as a remote piece of hardware used primarily in accounting and engineering departments, but instead as an important tool to be used increasingly in CAD and CAM. Today CAD and CAM have become closely linked for complete processing from design to production. The desin engineer can now create the desired design on a CRT screen that is linked to a computerized graphics plotter. The same system can be used to determine the viability of the design by analyzing stresses and deflections that will take place under loading conditions. The functioning of mechanical linkages may also be checked. After the design is complete, the production group can draw on the information developed in CAD for computer-aided manufacture. Thus the unified CAD-CAM team has been developed to bring the product from the design concept through manufacture. CAD Functions Initially CAD systems were primarily automated drafting stations in which computer plotters produced engineering drawings. The systems were later linked to graphic display terminals, which allowed the user to communicate with the computer in pictures instead of raw columns of numbers. Now advanced systems have added analytical capabilities. CAD functions may be grouped into four major categories: geometric modeling, engineering analysis, kinematics, and automated drafting. Geometric Modeling Traditionally, engineers do the sketching and drafts-men the drafting. Engineers then discover needed changes or improvements and draftsmen draft what is required. Moving a bracket 2 in, to the left causes an entree chain reaction throughout a complete set of drawings. Now the computer has opened up a new way to meet design engineering needs with speed and reliability in products ranging from high-performance aircraft to complex, integrated circuits. The designer can sketch directly on the screen of a graphics terminal. Lines and contours are defined by pressing keys and positioning a light pen, and the computer displays what is expressed. Curve fitting, or reducing the design to a set of control equations is done at the terminal, eliminating coding, card punching, punching, and repeated computer batch runs;then CAD converts the preliminary design to a dimensional drawing with auxiliary views. If the drawing reveals a problem of compatibility with a subassembly, the pieces can be moved around with the light pen. The computer then converts this pictorial representation to a mathematical model stored in the computer data base for later use. The model may be used or other CAD fuctions or it may be recalled and refined by the engineer at any point in the design process. Geometric modeling is often considered to be the most important feature of a CAD system because so many other design functions in the system depend heavily on the model. The geometric model may be used to create a finite element model of a structure for stress analysis. The model may also serve as an input for automated drafting to produce engineering drawings. If CAD/CAM systems are interfaced, the geometric model can be used to create NC tapes for fabricating the part. Most modeling is done with a wire frame that represents the part shape with interconnected line elements . Analysis After the geometric modeling is done, the CAD system allows the designer to move directly to analysis. With simple keyboard instructions, the computer is asked to calculate weight, volume, surface area, moment to inertia, or center of gravity of a part. However, the most powerful method of analyzing a part is by the finite element method. In this technique the structure is broken down into a network of simple element that the computer uses to determine stresses, deflections, and other structural characteristics. Such analysis requires the tremendous computational power of a mainframe computer. Kinematics Many CAD system have kinematic features for plotting or animating the motion of simple, hinged parts such as doors or cranks. Such analysis can ensure that moving components do not impact on other parts of the structure. The design of an automobile hood linkage, for example, requires only a few minutes of interaction with a computer, whereas hundreds of hours of hours can be required for manual design of the same part. Experts believe that in the future computers and programs will be available to completely synthesize a complex mechanical system based solely on its intended function. Drafting With automated drafting, detailed engineering drawings may be produced automatically from a data base. In addition, most drafting systems have automatic scaling and dimensioning features. A typical CAD system with automated drafting can generate up to six views on the screen. Any design change made on one view is automatically added to the others. CAM Functions CAM functions center around four main areas: numerical control, process planning, robotics, and factory management. Numerical control As stated previously, NC uses coded information to control machine tool movements. The computer can now generate a NC program directly from a geometric model of a part. Automatic capillaries are generalities linked to highly symmetric geometric and other specialized shapes. Process Planning Process planning is involved with the detailed sequence of production steps from start to finish. Essentially, the process plan describes the state of the workplace at each workstation. The use of computers as an aid to process planning is comparatively recent and has led to a rebirth of what is known as group technology (G T). Group technology is based on organizing all similar parts into families to allow standardization of fabricating steps. Currently under development is process planning system that is able to produce process plans directly from the geometric model database with almost no human assistance. In this system ,the process planner would review the impact from the design engineer via communication and then enter this input into the CAM system, which would generate a complete set of process plans automatically. Robotics Many advances are being made to integrate robotics into CAM. One of these efforts is the U.S. Air Force Integrated Computer-Aided Manufacturing (ICAM) project, of which the goal is to organize every step of manufacturing around computer automation. As part of this program, a robot is used to drill sheet metal aircraft parts. The robot selects drill bit from a tool rack, drills a set of holes to 0.005 in tolerance, and machines the perimeter of any one of 250 types of parts. Production rates are four times faster than conventional manual fabrication. Factory management This portion of CAM ties together the other areas to coordinate operations of an entire factory. The management system relies heavily on group technology with its families of similar parts. Computers also perform various management tasks such as inventory control and scheduling in systems that have come to be known as material requirements planning (MRP) systems. CAD / CAM技術 計算機技術以指數曲線的形式上升。僅僅在上一代以前電腦在數字控制方面還并不是真的需要。除相對較少為五軸聯動機。數字控制是點對點，這是很容易完成的手工編程。 面對兩維剖面，然而 ，需要進行眾多計算來產生輪廓曲線。在這一點上，計算機在制造工程方面看作是一個有用的工具。經過一番發展之后，發現用針刺或磁帶可完全免除對計算機程序的依賴，從而直接控制機器的正常運行。緊接著是微型電腦，它在與中央處理機的經營過程中帶來了自動化工廠的第一次真正的概念。 所有這些事態發展在技術進步方面都是重要的步驟。計算機已不再被看作是一個硬件而僅用于計算和工程部門，而是作為一個重要的工具，被日益廣泛地應用于CAD和CAM 中。 今天CAD和CAM已為了能夠完成從設計到生產的加工而緊密聯系在一起?，F(xiàn)在設計工程師可以在連接著一臺計算機化的圖形繪圖機的CRT屏幕上創造理想的設計。同一系統可以通過分析應力和撓度來確定設計的可行性，從而將在加載條件得到證明。運轉機械的聯系，也可以進行檢查。在設計完成后，制作小組可以借鑒國際上在CAD方面發達的信息用于電腦輔助制造。這樣，統一的CAD-CAM小組已經研制成功，使產品從設計理念過渡到制造。 CAD的作用 最初的CAD系統，主要是通過計算機繪圖制作工程圖紙來自動監測站起草工作。后來，系統和圖形顯示終端連接，使操作者可直接與計算機以圖形方式交流，代替了過去用原始數據的方式?，F(xiàn)在，先進的系統已經加入了分析能力。CAD的職能可分為四大類：幾何造型，工程分析，運動學和自動化起草。 幾何造型 在傳統上，工程師們做素描而制圖人員起草。這時工程師會發現需要進行調整或改進的地方，并需繪圖員起草。向左邊移動支架2英寸 ，會因為一套完整的草繪而引起一系列連鎖反應。 現在，計算機開辟了一條新的途徑，以滿足工程設計的需要，它在高性能的飛機，到復雜的集成電路這些產品方面具有快速和可靠的特點。設計者可以直接在屏幕上素描圖形終端。線和輪廓線的定義是通過按下按鍵和定位輕筆，從而在電腦顯示器上顯示 需要表達的內容。 曲線擬合，或降低設計到一套在終端已經完成的控制方程，從而消除編碼，卡沖床，沖壓，并重復電腦的運行軌道;這時CAD把初步設計轉換成三維輔助制圖。 如果繪畫揭示了一個與組件的相容性問題，這個組件就會圍繞光筆四周轉動。這時電腦就會把這個有代表性的圖案轉換成數學模型，從而儲存在電腦資料庫，以便日后使用。該模型也許被用到或在其它CAD 職能中或人們可能還記得，也有可能在任何一點上被工程師在設計過程中重新定義。 幾何造型，往往被認為是CAD系統中最重要的一個功能，因為很多其他的在系統上的功能設計嚴重依賴于模型。幾何模型可以被用來創造一個用于結構應力分析的有限元模型。該模型也可作為一項為自動化起草制作工程圖紙的投入。如果CAD / CAM系統是接口，幾何模型可以用來產生數字控制錄音帶編造的那部分。 大部分模型是用有代表部分的形狀與互聯線元素做成的一個線框。 分析 幾何造型被完成后， CAD系統就允許設計師直接進入分析。用簡單的鍵盤指令，使計算機計算重量，體積，表面積，時刻以慣性，或重心的一個組成部分。然而，對零件進行分析的最優方法是有限元分析。用這種技術，結構就會分解成一個網絡的簡單成分，然后電腦運用它去決定壓力，撓度，和其他結構特征。這樣的分析，需要巨大的計算能力的電腦主機。 運動學 許多CAD系統在策劃方面都有運動學特征或動畫的簡單運動，鉸鏈部位，如門或曲柄。這樣的分析，才能確保運動部件不影響其他部分的結構。例如設計汽車的聯動裝置，用計算機設計僅需幾分鐘，然而，人工設計同樣的部件要花費上百個小時。 專家認為，在未來，計算機和程序，將完全基于其預定的功能可合成一個復雜的機械系統。 自動化起草 用自動化起草機構，可以從資料庫自動產生詳細的工程圖紙。此外，大部分起草系統具有自動縮放及標注功能。 一個帶著自動化起草工作的典型的CAD系統，可以在屏幕上產生多達6個的觀點。對某一個觀點的任何設計變更的制作會自動添加給其他人。 CAM的功能 CAM的功能中心主要圍繞四個領域：數值控制，工藝設計，機器人和工廠管理。 數值控制 如前所述，數字控制用編碼信息來控制機床運動。 計算機可以將一個零件的幾何模型直接轉換為數字控制程序。自動毛細血管都是以高度對稱的幾何和其他專門的形狀泛泛的聯系在一起。 工藝規劃 工藝規劃從開始到結束涉及到詳細序列的生產步驟?；旧?，工藝方案在每一個工作站都描述了該區域的工作場所。使用計算機作為輔助工具的過程中的規劃是比較近的，并已導致了我們所熟悉的成組技術（ GT ）的重生。成組技術以組織全體類似零件進入某區域為基礎，并允許其進行標準化的制造步驟。 目前正在開發的是工藝設計系統，它能夠在幾乎沒有任何人的援助下直接從幾何模型數據庫中產生進程計劃。在這個系統中，這一過程規劃者將從同設計工程師通過交流審查其影響，然后再把它輸入到CAM系統中，這樣將產生一套完整的工藝方案自動。 機器人 CAM的許多改進得益于智能機器人技術的引入。其中的努力，是美空軍計算機集成計算機輔助制造（沿海）項目，其中的目標是組織管理圍繞計算機自動化生產的每一步。作為這項活動的一部分計劃，機器人將用于鉆飛機零部件的金屬板材。機器人從工具機架上選擇鉆頭，鉆了一套0.005英寸余量的洞 ，并且組裝了機器周邊250種零件中的任何一個。生產率是傳統的手工制作的4倍。 工廠管理 CAM技術的這部分和其他領域聯系在一起，用以協調整個一個工廠的操作。該管理系統在很大程度上依靠于成組技術及其領域的類似零件。電腦也做好各項管理工作，如庫存控制和調度系統，已被稱為物料需求計劃（ MRP ）系統。 9 第 頁