喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 數控鏟磨床縱向進給系統的設計 摘 要 鏟磨床是滾刀、成型銑刀等復雜刀具的精加工機床。由于傳統鏟磨床加工精度下降、生產效率低，工人勞動強度大，本設計對傳統鏟磨床的縱向進給機構進行數控化改造來改善其上述不足之處。 通過對目前工廠中傳統的鏟磨床進行研究，參考數控機床的相關文獻，了解鏟磨床縱向進給部分的工作原理，并深入分析鏟磨床在加工的過程中各個零部件的受力情況，按壽命計算選擇了絲杠的尺寸規格，并校核了額定動載荷、傳動效率、剛度，最終選擇了漢江機床廠生產的滾珠絲杠。通過對主軸受力的分析選擇了用推力球軸承承受軸向力，用深溝球軸承承受徑向力的形式。導軌的選取參考了漢江機床廠生產的滾動導軌，對導軌的壽命以及額定載荷進行了校核，均能滿足要求。電機根據滾珠絲杠的導程計算出的最高轉速，和傳動過程中的最大轉矩選取了富士公司的伺服電機并對轉動慣量進行了校核。由于采用了閉環系統，在查閱了光柵尺的相關參數后，選擇FAGOR公司的光柵尺能使在規定的行程內定位分辨率達到要求。 通過上述設計實現了鏟磨床縱向進給系統的數控化改造，滿足了加工精度的要求，具有加工穩定可靠，效率高等優點。 關鍵詞: 數控鏟磨床;縱向進給系統;精加工;閉環系統 Design of Longitudinal Feed System of CNC Relief Grinding Machine Abstract CNC relief grinding machine is a complex tool finishing machine for hobbing cutter, formed mill cutter. Because traditional relief grinding machine’s accuracy and production efficiency is low, the workers labor intensity is too big .The purpose of the numerical control reformation for the longitudinal feed system of traditional relief grinding machine is to improve the performance. After the traditional relief grinding machine had been researched in the factory at present, and reference related literature of CNC machine tools, The longitudinal feed part of relief grinding machine of working principle, and in-depth analysis of relief grinding machine in the process of machining force situation of every parts and components. According to the life of screw，chosed the size of screw. And checked the dynamic load rating, transmission efficiency, stiffness. Ultimately chose the ball screw produced by Hanjiang Machine Tool Factory . Through the analysis of the force acting on the spindle. A thrust ball bearing under axial force had been chosed, and a deep groove ball bearings bear radial force. With reference to the rolling guide produced by Hanjiang Machine Tool Factory, and calculating the life of rail and rated load, All parameters of guide can satisfied the requirements. According to the highest speed of the motor which is calculated according to the lead of ball screw and maximum torque of transmission process, The servo motor Fuji Corp had been chosed. And the moment of inertia is checked. Due to the adoption of the closed-loop system, the related parameters of grating ruler lookup, The grating ruler produced by FAGOR company had been chosed, which can satisfied that Positioning resolution meet the requirements stipulated in the distance. Through the design , Implementation of the NC transformation of relief grinding machine longitudinal feed system, It meet’s the requirement of processing precision , and the processing is stable and reliable, high efficiency. Key words:CNC relief grinding machine; Longitudinal feed system; Finish machining;Closed loop system 目 錄 1 緒論 1 1.1概述 1 1.2數控機床的優點 2 1.3數控機床的組成 3 2 總體方案設計 7 2.1機床的運動關系 7 2.2傳動方案的設計 7 2.2.1絲杠的選型及支撐方式的設計 7 2.2.2檢系統的選取 8 2.2.3導軌的選定 8 2.2.4絲杠和電機連接零件的選取 9 2.2.5軸承類型的選取 9 3 進給伺服系統機械部分計算與校核 10 3.1 滾珠絲杠螺母副的計算和選型 10 3.1.1額定動載荷 10 3.1.2傳動效率校核 12 3.2軸承的計算和選型 12 3.2.1推力球軸承的選型 12 3.2.2深溝球軸承的選型 13 3.3絲杠的剛度和穩定性校核 14 3.3.1 絲杠的剛度校核 14 3.3.2穩定性校核 15 3.4導軌的計算和選型 15 3.4.1滾動直線導軌副行程長度的壽命 15 3.5 伺服電機的計算和選型 16 3.5.1電機轉速的選取 17 3.5.2電機轉矩的計算 17 3.5.3轉動慣量的校核 18 3.6 編碼器的選型 18 4 進給系統機械部分結構設計 19 4.1進給伺服系統裝配圖的設計 19 4.2安裝過程中應注意的問題 19 5 總結 21 參考文獻 22 致 謝 23 畢業設計（論文）知識產權聲明 24 畢業設計（論文）獨創性聲明 25 6 1 緒論 1.1概述 我國目前機床總量為380萬余臺，而其中數控機床總數只有11.34萬臺，這說明我國機床數控化率不到3%。我們大多數制造業和企業的生產、加工設備大多數是傳統機床，而且半數以上是役齡在10年以上的舊機床。用這種機床加工出來的產品普遍存在質量差、品種少、成本高等缺點，因此這些產品在國際、國內市場上缺乏競爭了，這直接影響了企業的生存和發展。所以必須提高機床的數控化率。