購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。帶三維備注的都有三維源文件，由于部分三維子文件較多，店主做了壓縮打包，都可以保證打開的，三維預覽圖都是店主用電腦打開后截圖的，具體請見文件預覽，有不明白之處，可咨詢QQ:1304139763===========題目最后備注XX系列，只是店主整理分類，與內容無關，請忽視
河南機電高等專科學校畢業設計說明書
鎖蓋塑料成型工藝及模具設計
摘要：本設計題目為鎖蓋塑料成型工藝及模具設計，體現了板類塑料零件的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了設計者注塑模設計的基礎知識，為設計更復雜的注塑模具做好了鋪墊和吸取了更深刻的經驗。
本設計運用塑料成型工藝及模具設計的基礎知識，首先分析了塑件的成分及性能要求，為選取澆口的類型做好了準備；然后估算了塑件的體積，便于選取注塑機及確定型腔數量；最后分析了塑件的特征，確定模具的設計參數、設計要點及推出裝置的選取。
該塑件壁厚均勻，而且比較薄，不允許有推桿痕跡，一般采用推件板推出機構，推件板推出機構的機構特點是：脫模力大而均勻，運動平穩，無明顯的推出痕跡且不必另設復位機構。
關鍵詞：注塑模 澆口 推件板
injection mould design of the plastic parts of Capping
Abstract: The requirement ，content and direction of the design of the side gate plastic parts are embodied on this injection mould design of the plastic parts of Capping. The designer’s foundation knowledge of the injection mould design is reinforced and is able to design more complex injection mould through the design.
Through the foundation knowledge, firstly, the composion and the performance of the part is analyzed to choose the type of the gat advantagely. Secondly, the volume of the part is estimated to choose the injection molding machine and to determine the mould quantity conveniently. Lastly the character of the part is analyzed to determine the mould design parameter and design point and choose the ejection assembly.
Wall thickness of the part is even and more thinner. It is inadmissibility that there is the mark of push pole. Generality, stripper plate
machanism is used.Charcteristic of the stripper plate: the knockout press is large and even ,the movement is smooth.The mark of push is unapparent and it need not to install reset machanism.
Keywords: Injection mould, stripper plate
2