九噸級驅動橋懸臂式雙級主減速器設計【優秀課程畢業設計含2張CAD圖紙帶任務書+開題報告+中期報告表+答辯ppt+外文翻譯】

九噸級驅動橋主減速器設計

摘要：主減速器、差速器、半軸和橋殼是驅動橋內部組成最重要的四個部分，我們都知道，驅動橋其最重要也是其最基礎的功能，是為了能夠增大從傳動軸或變速器兩方面所傳來的轉矩，然后再把轉矩分配給所需的驅動車輪使用，讓驅動車輪具有我們想要的那種差速功能；此外，其還要具有能經受各種力或者力矩的能力。

作為汽車最重要的組成部分，驅動橋的好與不好將會直接影響我們設計汽車的整體性能，而對于大型載貨汽車來說，其就會顯得更加重要。為了能達到汽車在重載的高效率和高效益，我們要為汽車安裝一個具有高效率的驅動橋。而我們還應考慮其地的一些問題，比如其最小離地間隙，所以我們設計時的齒輪要小些。判斷各種原因后，本次設計我決定選用一款雙級主減速器，參照我們傳統的設計方法來進行。本設計我的首要目標，就是確定的設計部件的結構和參數；我又參考了其他主減速器結構，給出了本次總體設計方案；最后，我還為主、從動錐齒輪也進行了使用壽命的校核工作。本次設計決定選用圓弧錐齒輪來作為汽車的主減速器。

    關鍵字：圓弧錐齒輪；主減速器；驅動橋；貨車

Design of the main reducer of nine ton drive axle

Abstract: Drive from the main bridge general reducer, differential, axle and axle housing is composed of four parts, its basic function is to increase the drive shaft or by direct torque transmission to the torque distribution to the left and right wheels, and the left and right wheels can have driving the differential kinematics in addition, function; also can take effect on the road and the frame or a carriage between the vertical force, longitudinal force and lateral force.

   As one of the four major automobile drive axle assembly, its performance will have a direct impact on vehicle performance, and it is particularly important for the truck. When a large high-power engine torque output to meet the current truck fast, heavy load high efficiency, need high efficiency, must be an efficient and reliable collocation drive bridge. Considering there must be sufficient ground clearance, the size of the internal gear drive axle can not be too large, so a two-stage main reducer. According to the traditional design method of main drive axle reducer of 9 ton truck drive axle main reducer design. Firstly, determine the main structure type the main components and To design parameters; and then refer to the similar driving axle main reducer structure, determine the overall design plan; at the end of the main, driven bevel gear check the life-span. This paper does not use the traditional hypoid gear as truck main reducer, instead of using the arc bevel gear.

   Key words: truck; drive axle; double speed reducer; arc bevel gear

目  錄

摘要................................................................................................................................I 

Abstract.......................................................................................................................II 

目錄....................................................................................................................III

1  緒論....................................................................................................1

1.1  驅動橋結構分析...........................................................................................1

2  主減速器設計................................................................................................3

2.1  主減速器概述.......................................................................................................3

2.2  主減速器齒輪的支承方式...................................................................................3

2.3  主減速器軸承預緊...............................................................................................4

2.4  錐齒輪嚙合的調整...............................................................................................4

2.5  潤滑.......................................................................................................................5

2.6  主減速器的結構形式...........................................................................................5

2.6.1  主減速器的齒輪類型........................................................................................5

2.6.2  主減速比的確定..............................................................................................5

2.6.3  主、從動錐齒輪支承型式...............................................................................6

2.7   主減速器參數的選擇與計算...........................................................7

2.7.1  主減速器齒輪載荷的計算........................................................................7

2.7.2  主減速器齒輪基本參數的選擇................................................................8

2.7.3  主減速器圓弧錐齒輪尺寸計算..................................................................9

2.7.4  主減速器圓弧錐齒輪強度計算................................................................10

2.7.5  主減速器齒輪材料及其熱處理......................................................................14

2.7.6  主減速器軸承的計算...............................................................................15

3  技術經濟分析..............................................................................................22

4  結論................................................................................................................23

參考文獻...............................................................................................................24

致謝.....................................................................................................................25

附錄..............................................................................................................................26

【詳情如下】【需要咨詢購買全套設計請加QQ1459919609】

主動圓錐齒輪軸.dwg

九噸級驅動橋主減速器設計.docx

九噸級驅動橋主減速器設計開題報告.doc

九噸級驅動橋主減速器設計答辯PPT.pptx

九噸級驅動橋懸臂式雙級主減速器設計中期報告.doc

九噸級驅動橋懸臂式雙級主減速器設計任務書.doc

外文翻譯.docx

文件清單.txt

裝配圖.dwg