購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
畢業設計(或論文)說明書 共17頁
附錄1
Industrial Robots and Electric drive system
There are a variety of definitions of the term robot. Depending on the definition used, the number of robot installations worldwide varies widely. Numerous single-purpose machines are used in manufacturing plants that might appear to be robots. These machines are hardwired to perform a single function and cannot be reprogrammed to perform a different function. Such single-purpose machines do not fit the definition for industrial robots that is becoming widely accepted. This definition was developed by the Robot Institute of America:
A robot is a reprogrammable multifunctional manipulator designed to move material, parts, tools, or specialized devices through variable programmed motions for the performance of a variety of tasks.
Note that this definition contains the words reprogrammable and multifunctional. It is these two characteristics that separate the true industrial robot from the various single-purpose machines used in modern manufacturing firms. The term “reprogrammable” implies two things: The robot operates accommodate a variety of manufacturing tasks.
The term “multifunctional” means that the robot can, through reprogramming and the use of different end-effectors, perform a number of different manufacturing tasks. Definitions written around these two critical characteristics are becoming the accepted definitions among manufacturing professionals.
The first articulated arm came about in 1951 and was used by the U.S. Atomic Energy Commission. In 1954, the first programmable robot was designed by George Devil. It was based on two important technologies:
Numerical control (NC) technology.
Remote manipulator technology.
Numerical control technology provided a form of machine control ideally suited to robots. It allowed for the control of motion by stored programs. These programs contain data points to which the robot sequentially moves, timing signals to initiate action and to stop movement, and logic statements to allow for decision making.
Remote manipulator technology allowed a machine to be more than just another NC machine. It allowed such machines to become robots that can perform a variety of manufacturing tasks in both inaccessible and unsafe environments. By merging these two technologies, Devil developed the first industrial robot, an unsophisticated programmable materials handling machine.
The first commercially produced robot was developed in 1959. In 1962, the first industrial robot to be used on a production line was installed by General Motors Corporation. This robot was produced by Animation. A major step forward in robot control occurred in 1973 with the development of the T-3 industrial robot by Cincinnati Milacron. The T-3 robot was the first commercially produced industrial robot controlled by a minicomputer.
Numerical control and remote manipulator technology prompted the wide-scale development and use of industrial roots. But major technological developments do not take place simply because of such new capabilities. Something must provide the impetus for taking advantage of these capabilities. In the case of industrial robots, the impetus was economics.
The rapid inflation of wages experienced in the 1970s tremendously increased the personnel costs of manufacturing firms. At the same time, foreign competition became a serious problem for U.S. manufacturers. Foreign manufacturers who had undertaken automation on a wide-scale basis, such as those in Japan, began to gain an increasingly large share of the U.S. and world market for manufactured goods, particularly automobiles.
Through a variety of automation techniques, including robots, Japanese manufacturers, beginning in the 1970s, were able to produce better automobiles more cheaply than no automated U.S. manufacturers. Consequently, in order to survive, U.S. manufacturers were forced to consider any technological developments that could help improve productivity.
Though a variety of automation techniques, including robots, Japanese manufacturers, beginning in the 1970s, were able to produce better automobiles more cheaply than no automated U.S. manufacturers. Consequently, in order to survive, U.S. manufacturers were forced to consider any technological developments that could help improve productivity.
It became imperative to produce better products at lower costs in order to be competitive with foreign manufacturers. Other factors such as the need to find better ways of performing dangerous manufacturing tasks contributed to the development of industrial robots. However, the principal rationale has always been, and is still, improved productivity.
One of the principal advantages of robots is that they can be used in settings that are dangerous to humans. Welding and parting are examples of applications where robots can be used more safely than humans, Even though robots are closely associated with safety in the workplace, they can, in themselves, be dangerous.
Robots and robot cells must be carefully designed and configured so that they do not endanger human workers and other machines. Robot work envelopes should be accurately calculated and a danger zone surrounding the envelope clearly marked off. Red flooring strips and barriers can be used to keep human workers out of a robot’s work envelope.
Even with such precautions it is still a good idea to have an automatic shutdown system in situations where robots are used. Such a system should have the capacity to sense the need for an automatic shutdown of operations. Fault-tolerant computers and redundant systems can be installed to ensure proper shutdown of robotics systems to ensure a safe environment.
The robot electrically operated servo drive system sds is uses the moment of force and the strength which each kind of electric motor produces, directly or indirectly actuates the robot main body to obtain the robot each kind of movement implementing agency. The electric motor actuates which to the industry robot joint, the request has the maximum work rate quality compared to with the torque inertia compared to, rises up the dynamic torque, the is low inertia and broader also the smooth velocity modulation scope. Specially (hand fingernail) should use the volume, the quality as far as possible small electric motor like the robot terminal execution, when in particular requests the fast response, the servo motor must have a higher reliability and the stability, and has the bigger momentary overload ability. This is the servo motor in the industry robot the application precondition.
The robot actuates the electrical machinery to the joint overriding demand the gauge natrium as follows:
1) rapidity. The electric motor from obtains the command signal to complete the active status time which the instruction requests to be supposed to be short. Response command signal time shorter, the electricity servosystem sensitivity higher, the fast response performance is better, generally is explains the servo motor fast response by the servo motor mechanical and electrical time-constant size the performance.
2) the starting moment inertia is bigger than. In in the actuation load situation, requests the robot the servo motor starting moment in a big way, the rotation inertia is small.
3) the control characteristic continuity and the straight line, along with the control signal change, the electric motor rotational speed can continuously change, sometimes also needs the rotational speed and the control signal has the direct ratio or approximately has the direct ratio.
4) modulates velocity the scope to be wide. Can use to 1: 1,000 ~ 10,000 velocity modulation scopes.
5)the volume small, the quality small, the axial size is short.
6) can undergo the harsh movement condition, may carry on the extremely frequent pro and con to and adds and subtracts the fast movement, and can withstand the overload in the short time.
Industry robot direct motor drive principle like chart 1 shows. The industry robot electrically operated servosystem general structure is three closed-loops control, namely electric current link, speed ring and snap ring.
At present the overseas many electric motors produce the factory to develop the actuation product which suitably matches with the exchange servo motor, the user act according to oneself need the function stress to choose the different servo-control way differently, in the ordinary circumstances, exchanges the servo driver below, passable has carried on the artificial hypothesis to its internal function parameter to realize the function:
1) position control way;
2) speed control way;
3) torque control mode;
4) position, speed mixed mode;
5) position, torque mixed mode;
6)speed, torque mixed mode;
7) torque limitation;
8) the position deviation oversized reports to the police;
9) speed PID parameter establishment;
10) speed and acceleration forward feed parameter establishment;
11) zero floats compensates the parameter establishment;
12) adds and subtracts the fast time establishment and so on
1. direct current servo motor driver direct current servo motor driver to use the pulse-duration modulation (PWM) the servo driver, changes through the change pulse width adds in the motor armature beginnings and ends average voltage, thus changes the electric motor the rotational speed. The PWM servo driver has the velocity modulation scope width, the low-speed characteristic well, responds, the efficiency quickly high, the overload capacity is strong and so on the characteristic, often takes the direct current servo motor driver in the industry robot.
2. synchronized types exchange servo motor driver same direct current servo motor actuates the system to compare, the synchronized type exchange servo motor driver has the torque rotation inertia electronics brush and commutation spark merit and so on to be higher than, not to have, obtains the widespread application in the industry robot. The synchronized type exchange servo motor driver usually uses the electricity flow pattern pulse-duration modulation (PWM) the inversion and has the electric current link for the inner rim, the speed ring for the outer ring multi- closed-loop control system, realizes to the three-phase permanent magnetism synchronization servo motor electric current control. According to its principle of work, the actuation current waveform and the control mode difference, it may divide into two kind of servosystems:
1) rectangular wave electric current actuation permanent magnetism A.C. servomechanism.
2) sinusoidal current actuation permanent magnetism A.C. servomechanism. Uses the rectangular wave electric current actuation the permanent magnetism exchange servo motor to be called not brushes the direct current servo motor, uses he sinusoidal current actuation the permanent magnetism exchange servo motor to be called not brushes the exchange servo motor.
3. direct drives so-called direct drives (DD) the system, is the load conductive coupling which the electric motor if actuates in the same place, middle does not have any reduction gear. The same traditional electric motor servo actuates to compare, the DD actuation reduced the reduction gear, thus reduced the gap which in the system transmission process the reduction gear produces and becomes less crowded, enormously increased the robot precision, simultaneously also reduced because the reduction gear friction and the transmission torque pulsation creates the robot control precision reduces. But DD actuation because has above merit, therefore mechanical rigidity good, may the high speed high accuracy movement, also has the part few, the structure simple, is easy to service, the reliable higher characteristic, in the high accuracy, in the high speed industry robot application more and more brings to people's attention. As the DD actuation technology essential link is the DD electric motor and its the driver. Below it should have the characteristic:
1) outputs the torque in a big way: For tradition drive type in servo motor output torque 50 ~ 100 times.
2) torque pulsation small: The DD electric motor torque pulsation may suppress in the output torque 5% ~ in 10%.
3) efficiency: With uses the reasonable impedance matching the electric motor (under tradition drive type) to compare, the DD electric motor is works under the power conversion worse exploitation conditions. Therefore, the load is bigger, more favors to selects a bigger electric motor.
At present, the DD electric motor mainly divides into changes the magnetic resistance and changes the magnetic resistance mixed type, has following two kind of structures pattern:
1) the double stator structure changes the magnetic resistance DD electric motor;
2) the central stator structure changes the magnetic resistance mixed type DD electric motor.
5. special drivers
1)piezoelectricity driver. It is well known, has made using the piezoelectricity part electricity or the electrostriction phenomenon should the variant acceleration instrument and the ultrasonic sensor, the piezoelectricity driver use the site of electrical energy controls several microns to several hundred microns displacements in is higher than the micron level big strength, therefore the piezoelectricity driver generally uses in the special use miniature robot assembly system.
2) ultrasonic wave electric motor.
3) the vacuum electric motor, uses in the vacuum robot which under the ultra pure environment works, for example uses in to transport the semiconductor silicon chip the ultra vacuum robot and so on.
附錄2
工業機器人及電動驅動系統
有許多關于機器人這個術語的定義。采用不同的定義，全世界各地機器人的數量就會發生很大的變化。 在制造工廠中使用的許多單用途機器可能會看起來像機器人。這些機器是硬連線的，不能通過重新編程的方式去完成不同的工作。這種單用途的機器不能滿足人們?nèi)找鎻V泛接受的關于工業機器人的定義。這個定義是由美國機器人協會提出的：
機器人是一個可以改變程序的多功能操作器，被設計用來按照預先編制的、能夠完成多種作業的運動程序運送材料、零件、工具或者專用設備。
注意在這個定義中包含有“可以改變程序”和“多功能”這兩個詞。正是這兩個詞將真正的機器人與現代制造工廠中使用的單一用途的機器區分開來?！翱梢愿木幊绦颉边@個術語意味著兩件事：機器人根據編寫的程序工作，以及可以通過重新編寫程序來適應不同種類的制造工作的需要。
“多功能”這個詞意味著機器人能通過編程和使用不同的末端執行機構，來完成不同的制造工作。圍繞著這兩個關鍵特征所撰寫的定義正在變成為制造業的專業人員所接受的定義。
第一個帶有活動關節的手臂于1951年被研制出來，由美國原子能委員會使用。在1954年，第一個可以編程的機器人有喬治.狄弗設計出來。它基于下面兩項重要技術：
數字控制（NC）技術。
遠程操作器技術。
數字控制技術提供了一種非常適合于機器人的機器控制技術。它可以通過儲存的程序?qū)\動進行控制。這些程序包含機器人進行順序運動的數據，開始運動和停止運動的時間控制信號，以及做出決定所需要的邏輯語句。
遠程操作器技術使得一臺機器的性能超出一臺數控機器。它可以使這種機器能夠在不容易進入和不安全的環境中完成各種制造任務。通過融合了上述兩項技術，狄弗研制出第一個機器人，它是一個不復雜的，可以編程的物料運送機器人。
第一臺商業化生產的機器人在1959年研制成功。通用汽車公司在1962年安裝了第一臺用于生產線上的工業機器人，它是尤尼梅森公司生產的。在1973年，辛辛那提.米蘭克朗公司研制出T-3工業機器人，在機器人的控制方面取得了較大的進展。T-3機器人是第一臺商業化生產的采用計算機控制的機器人。
數字控制技術和遠程操作器技術推動了大范圍的機器人研制和應用。但是主要的技術進步并不僅僅上由于這些新的應用能力而產生的，而是必須由利用這些能力所得到的效益來提供動力。就工業機器人而言，這個動力是經濟性。
在20世紀70年代中，工資的快速增長大大增加了制造業的企業中的人工費用。與此同時，來自國外的競爭成為美國制造業所面臨的一個嚴峻的考驗。諸如日本等外國的制造廠家在廣泛地應用了自動化技術之后，其工業產品，特別是汽車，在美國和世界時常中占據了日益增大的分額。
通過采用包括機器人在內的各種自動化技術，從70年代開始，日本的制造廠家能夠比沒有采用自動化技術的美國制造廠家生產更好的和更便宜的汽車。隨后，為了生存，美國制造廠家被迫考慮采用任何能夠提高生產率的技術。
為了與國外制造廠家進行競爭，必須以比較低的成本，生產出更好的產品。其他的因素，諸如尋找能夠更好地完成帶有危險性的制造工作的方式也促進了工業機器人的發展。但是，主要的理由一直是，而且現在仍然是提高生產率。
機器人的一個主要優點是它們可以在對于人類來說是危險的位置上工作。采用機器人進行焊接和切斷工作上比由人工來完成這些工作更安全的例子。盡管機器人與工作地點的安全密切相關，它們本身也可能是危險的。
應該仔細地設計和配置機器人和機器人單元，使它們不會傷害人類和其他機器。應該精確地計算出機器人的工作范圍，并且在這個范圍的四周清楚地標出危險區域?？梢圆捎迷诘孛嫔袭嫵黾t顏色的線和設置障礙物以阻止工人進入機器人的工作范圍。
即使有了這些預防措施，在使用機器人的場地中設置一個自動停止工作的系統仍然上不失為一個好主意。機器人的這個系統應該具有能夠檢測出是否有需要自動停止工作的要求的能力。為了保證能有一個安全的環境，應當安裝容錯計算機和冗余系統來保證在適當?shù)臅r候停止機器人的工作。
機器人電動伺服驅動系統是利用各種電動機產生的力矩和力，直接或間接地驅動機器人本體以獲得機器人的各種運動的執行機構。
對工業機器人關節驅動的電動機，要求有最大功率質量比和扭矩慣量比、高起動轉矩、低慣量和較寬廣且平滑的調速范圍。特別是像機器人末端執行器（手爪）應采用體積、質量盡可能小的電動機，尤其是要求快速響應時，伺服電動機必須具有較高的可靠性和穩定性，并且具有較大的短時過載能力。這是伺服電動機在工業機器人中應用的先決條件。
機器人對關節驅動電機的主要要求規納如下：
1）快速性。電動機從獲得指令信號到完成指令所要求的工作狀態的時間應短。響應指令信號的時間愈短，電伺服系統的靈敏性愈高，快速響應性能愈好，一般是以伺服電動機的機電時間常數的大小來說明伺服電動機快速響應的性能。
2）起動轉矩慣量比大。在驅動負載的情況下，要求機器人的伺服電動機的起動轉矩大，轉動慣量小。
3）控制特性的連續性和直線性，隨著控制信號的變化，電動機的轉速能連續變化，有時還需轉速與控制信號成正比或近似成正比。
4）調速范圍寬。能使用于1：1000～10000的調速范圍。
5）體積小、質量小、軸向尺寸短。
6）能經受得起苛刻的運行條件，可進行十分頻繁的正反向和加減速運行，并能在短時間內承受過載。
工業機器人電動伺服系統的一般結構為三個閉環控制，即電流環、速度環和位置環。
目前國外許多電動機生產廠家均開發出與交流伺服電動機相適配的驅動產品，用戶根據自己所需功能側重不同而選擇不同的伺服控制方式，一般情況下，交流伺服驅動器，可通過對其內部功能參數進行人工設定而實現以下功能：
1）位置控制方式
2）速度控制方式；
3）轉矩控制方式；
4）位置、速度混合方式；
5）位置、轉矩混合方式；
6）速度、轉矩混合方式；
7）轉矩限制；
8）位置偏差過大報警；
9）速度PID參數設置；
10）速度及加速度前饋參數設置；
11）零漂補償參數設置；
12）加減速時間設置等
1．直流伺服電動機驅動器
直流伺服電動機驅動器多采用脈寬調制（PWM）伺服驅動器，通過改變脈沖寬度來改變加在電動機電樞兩端的平均電壓，從而改變電動機的轉速。
PWM伺服驅動器具有調速范圍寬、低速特性好、響應快、效率高、過載能力強等特點，在工業機器人中常作為直流伺服電動機驅動器。
2．同步式交流伺服電動機驅動器
伺服電動機驅動系統相比，同步式交流伺服電動機驅動器具有轉矩轉動慣量比高、無電刷及換向火花等優點，在工業機器人中得到廣泛應用。
同步式交流伺服電動機驅動器通常采用電流型脈寬調制（PWM）相逆變器和具有電流環為內環、速度環為外環的多閉環控制系統，以實現對三相永磁同步伺服電動機的電流控制。根據其工作原理、驅動電流波形和控制方式的不同，它又可分為兩種伺服系統：
1）矩形波電流驅動的永磁交流伺服系統。
2）正弦波電流驅動的永磁交流伺服系統。
矩形波電流驅動的永磁交流伺服電動機稱為無刷直流伺服電動機，采用正弦波電流驅動的永磁交流伺服電動機稱為無刷交流伺服電動機。
3．直接驅動
驅動（DD）系統，就是電動機與其所驅動的負載直接耦合在一起，中間不存在任何減速機構。
同傳統的電動機伺服驅動相比， DD驅動減少了減速機構，從而減少了系統傳動過程中減速機構所產生的間隙和松動，極大地提高了機器人的精度，同時也減少了由于減速機構的摩擦及傳送轉矩脈動所造成的機器人控制精度降低。而DD驅動由于具有上述優點，所以機械剛性好，可以高速高精度動作，且具有部件少、結構簡單、容易維修、可靠性高等特點，在高精度、高速工業機器人應用中越來越引起人們的重視。
作為DD驅動技術的關鍵環節是DD電動機及其驅動器。它應具有以下特性：
1）輸出轉矩大：為傳統驅動方式中伺服電動機輸出轉矩的50～100倍。
2）轉矩脈動小： DD電動機的轉矩脈動可抑制在輸出轉矩的5％～10％以內。
3）效率：與采用合理阻抗匹配的電動機（傳統驅動方式下）相比， DD電動機是在功率轉換較差的使用條件下工作的。因此，負載越大，越傾向于選用較大的電動機。
目前，DD電動機主要分為變磁阻型和變磁阻混合型，有以下兩種結構型式：
l）雙定子結構變磁阻型DD電動機；
2）中央定子型結構的變磁阻混合型DD電動機。
5．特種驅動器
1）壓電驅動器。眾所周知，利用壓電元件的電或電致伸縮現象已制造出應變式加速度傳感器和超聲波傳感器，壓電驅動器利用電場能把幾微米到幾百微米的位移控制在高于微米級大的力，所以壓電驅動器一般用于特殊用途的微型機器人系統中。
2）超聲波電動機。
3）真空電動機，用于超潔凈環境下工作的真空機器人，例如用于搬運半導體硅片的超真空機器人等。
附錄3
17