【機械類畢業論文中英文對照文獻翻譯】動力減振鏜桿結構參數優化,機械類畢業論文中英文對照文獻翻譯,機械類,畢業論文,中英文,對照,對比,比照,文獻,翻譯,動力,減振鏜桿,結構,參數,優化 遼寧工程技術大學畢業設計（論文） 附錄A 動力減振鏜桿結構參數優化 　　摘要：深孔鏜削過程中，鏜桿不可避免產生振動，影響孔的加工質量，為了提高加工質量，本文針對動力減振鏜桿建立力學模型，通過對模型的研究得出減振器的最優參數，應用ADAMS動力學仿真軟件和試驗驗證了理論優化的正確性。通過和普通鏜桿對比分析，結果表明動力減振鏜桿有效地達到了減振效果。 關鍵詞：減振器結構；動態性能；參數優化 1．引言 在深孔鏜削過程中，受到孔的尺寸限制，鏜桿長徑比較大，剛度小，固有頻率低，在受到機床自身激勵和外部激勵時，很容易發生振動，影響工件的加工精度和表面質量。三菱公司通過減輕鏜桿頭部的的重量來提高鏜桿的剛度，美國Kenametal公司生產的減振鏜桿 (最大長徑比 L /D = 8 ) 主要采用特殊材料來提高鏜桿靜剛度,這些方法受到長徑比的限制。 動力減振鏜桿可以進一步提高長徑比，在深孔加工方面具有很大的優勢。Warburton通過對附加在鏜桿上的減振器的參數進行優化來實現對主系統的減振，減振器包括彈簧，阻尼和減振塊。在載荷作用下， J iaJang W u研究了減振器螺旋彈簧的慣性效應對鏜桿動態特性的影響。Felipe Antonio Chegury Viana等人基于蟻群算法設計出可調動態減振器。這些方法所設計出的動力減振鏜桿成本較高，結構復雜，維護麻煩，當前應用不廣泛。 針對上述問題，下面將采用虛擬樣機技術，在ADAMS環境下進行減振器結構優化，最后進行實驗驗證，通過對比分析，表明理論優化的結果、仿真結果和實驗結果基本一致，降低了設計成本。 2．動力減振鏜桿理論及建模 動力減振是將主系統的能量轉移到減振器系統上，減小主系統的振動。減振鏜桿結構如圖1所示，建立的力學模型如圖 2所示。動力學方程可表示為 主系統的振動幅值為 對不同的ξ值所作出的主系統的幅頻響應曲線如圖3所示，當ξ =∞時，鏜桿和減振器之間沒有相對運動，成為單自由度系統，時其幅頻曲線只有一個峰值，等效于普通鏜桿。當 ξ介于 0和∞之間時，系統為兩自由度，產生兩個共振點。阻尼的存在使主系統的共振幅值減少，但并不能完全消除主系統的振動。圖 3中所有的曲線都相交于P、Q兩點, 表明P、Q兩點的頻率和幅值與 ξ的變化無關，得出方程式為 求出 P、Q 兩點的頻率,帶入( 2 )式得到 P、Q兩點的幅值。從 ( 2 ) 、( 3 ) 式可以看出，對確定的主系統而言，幅值和頻率取決于減振器的質量和彈簧。減振器最理想的結構參數應該是在P、Q兩點達到峰值，并且數值相等。根據這種思路，可按下述步驟選擇減振器的最優參數。 對于確定的主系統和選定的減振塊質量，結構最優參數解為： 進而確定減振器的剛度 在 P、Q兩點取駐點的條件下，求得減振器的阻尼率ξ 3．動力學仿真 為了驗證所建模型的有效性，在ADAM S環境下進行仿真。應用ADAMS中有限元模塊將鏜桿桿體模型轉變成柔體，在刀頭端部創建輸入和輸出通道，然后進行系統的振動分析，通過仿真計算，在后處理模塊中得出系統的模態和頻響函數。 減振器初始參數，，。鏜桿桿體的結構尺寸：直徑D = 0. 016 m ,長度L =0. 192 m ,長徑比為12: 1；材料屬性：密度ρ= 7 801 kg/m，彈性模量E = 2. 07E + 011 N /m2，泊松比ν= 0. 29。根據結構圖建立振動模型。 減振塊質量的變化對幅頻曲線的影響。當m 2 = 0. 02 kg時，得到前兩階自然頻率為253 Hz和452 Hz,共振時的最大幅值為- 95. 16 dB 和- 103. 3 dB；當m 2 = 0. 10 kg時，前兩階的自然頻率為128 Hz 和406 Hz，共振時的最大幅值為- 95. 2 dB - 95. 3 dB。對不同的質量值繪制主系統的幅頻響應曲線如圖4所示?？梢钥闯鲎匀活l率隨著減振塊質量的增加而降低，當外部激勵的頻率與主系統的自然頻率接近時，可以通過修改減振塊質量的方法來避免發生共振，而減振塊質量對幅值的影響不敏感。 圖 4 頻響函數隨質量變化曲線 阻尼的變化對幅頻特性曲線的影響。當c2 = 10 N s/m時，前兩階自然頻率為 253 Hz和 452 Hz,共振時最大幅值為- 94. 75 dB 和- 103. 24 dB；c2 = 2 N s/m ,前兩階的自然頻率為 253 Hz 和 452 Hz, 共振時最大幅值為 - 90. 11 dB , 和 - 95. 49 dB。圖5為振動分析后繪制的頻響曲線圖，表明阻尼的變化對幅值的影響比較大，幅值隨阻尼的增大而減小，當共振不可避免時，通過修改阻尼來減小振幅，而阻尼對自然頻率的影響不太明顯。 圖 5 頻響函數隨阻尼變化曲線 剛度的變化對幅頻特性的影響。當剛度 k2 = 10 kN /m時，前兩階的自然頻率為 253 Hz和 452 Hz，共振時的最大幅值為 - 94. 71 dB 和 - 108. 20 dB; 當 k2 = 200 kN /m 時，前兩階的自然頻率為 284 Hz和 898 Hz, 共振時的最大幅值為 - 90. 27 dB和 - 110. 06 dB。圖6為繪制的頻響函數圖，表明自然頻率隨剛度的增加而增大，剛度的變化對幅值的影響比較大，通過修改剛度可避免共振和調整幅值。 圖 6 頻響函數隨剛度變化曲線 4．減振優化 根據動力減振鏜桿振動分析模型，以減振器的剛度和阻尼作為設計變量，使用ADAMS中View變量和振動宏作為目標函數，使目標函數最小。約束條件為振動幅值小于減振器和鏜桿內腔之間的距離，優化采用OPTDES-GRG廣義遞減梯度算法。參數優化的目的就是在給定的鏜桿結構和減振塊質量一定的條件下，優化出減振器的剛度和阻尼參數，當采用最優參數時主系統的振動幅值最小。當減振塊質量 m 2 =0. 021 44 kg，優化后的曲線和普通鏜桿曲線如圖 7所示。 圖 7 普通鏜桿和優化后減振鏜桿 優化后減振器的參數是 k2 = 58 662 N /m，c2 = 22. 34N s/m，前三階的自然頻率為 228 Hz、309 Hz和 392 Hz,前兩階的自然頻率的比值 0. 7378，根據公式 ( 4)計算出前兩階自然頻率的比值為 0. 7376,相對誤差為 0. 04%。仿真優化的阻尼率為 0. 221,公式 ( 6)得出的阻尼率為 0. 216,相對誤差為 2. 2%。根據上述定量分析，得出仿真優化和理論優化結果基本一致，表明仿真優化有效可行。 從圖 7中可以看出，在激勵條件不變的情況下，與普通鏜桿相比，減振鏜桿的振型得到明顯的改善，振型變得更加光滑，幅值也明顯減小。共振時最大幅值為 - 102. 33 dB，根據信號處理理論，實際幅值和曲線幅值的對應關系 M agnitude為仿真曲線幅值，根據上式得到實際振幅為0. 007 6 mm。普通鏜桿與優化減振鏜桿對比見下表，表明在長徑比較大的情況下，動力減振鏜桿振動幅值僅是普通鏜桿幅值的 23%，具有很好的減振效果。 5. 結論 在動力學仿真技術的基礎上，較為系統的探討了動力減振鏜桿的動態特性，以及減振器參數的變化對主系統的影響，并對參數進行優化，參數優化結果和理論優化結果吻合良好，最后通過和加工范圍。該方法對于進一步提高深孔加工領域的水平和相關技術的研究具有十分重要的理論意義和實際應用價值。 參考文獻 [1] D G Lee, H Y Hwang and J K Kim. Design and manufacture of acarbon fiber epoxy rotating boring bar [ J ]. Composite Structures,2003, 60 ( 1) : 115～124. [2] SANJ I G TEWAN I, KE ITH E ROUCH and BRUCE L WALCOTT A study of cutting p rocess stability of a boring bar with ac2tive dynam ic absorber [ J ]. I Mach. Tools Manufact 1995, 35 ( 1) : 91～108. [3] G B W arburton. Op tim um absorber parameters for m inim izing vibration response[ J ]. Journal of Earthquake Engineering and Structural Dynam ics , 1981, 9: 251～262. [4] J ia - Jang W u . Study on the inertia effect of helical sp ring of the absorber on suppressing the dynam ic responses of a beam subjected to a moving load [ J ]. Journal of Sound and V ibration. 2006, 297 ( 3- 5) : 981～999. [5] Felipe Antonio Chegury V iana, Giovanni Iam in Kotinda, Tuningdynam ic vibration absorbers by using ant colony op tim ization [ J ].Computers and Structures, 2008, 86 ( 13～14) : 1539～1549. [6]　邵俊鵬 ,秦柏.基于ADAMS的動力減振鏜桿仿真分析 [ J ].機械設計與研究 , 2008, 24 ( 1) : 84～88. [7]　師漢民. 機械振動系統 — 、分析 測試 建模 對策 [M ]. 武漢 :華中科技大學出版社 , 2004. 附錄B A Study of Optimum Parameters of A Boring Bar with Passive Dynamic Absorber Abstract: The vibration of the boring bar directly affects the processing quality in the deep hole machining In order to improve the processing quality, theoretical model of a boring bar with passive dynamic absorber has been developed and derived the optimum parameters of the absorber Both the dynamic simulation based on ADAM S and the experim ents were conducted to verify the theory Comparing w ith boring bar, numerical results reveal that boring bar with dynamic absorber has the effect of vibration decrease. Keywords: passive dynamic absorber structure; dynamic character; optimum parameter 1. Introduction In the process of deep-hole boring, restricted by the size of holes, boring bar larger aspect ratio, stiffness of small, low natural frequencies. Inspired by the machine itself and external incentives, it is prone to vibration, impact on the machining accuracy and workpiece surface quality. Mitsubishi boring bar by reducing the weight of the head of the boring bar to increase the stiffness, the United States produced Kenametal vibration boring bar (maximum aspect ratio L / D = 8) the main use of special materials to increase the static stiffness boring bar, which aspect ratio method by the restrictions. Driving force for boring bar vibration can be further enhanced aspect ratio, and has great advantage in the deep processing of. Through the pole attached to the parameters of the shock absorber,Warburton achieve the main system of the vibration, shock absorber, including springs, dampers and damping block. In the load, J iaJang W u studied coil spring shock absorber of the inertial effect on the dynamic properties of boring bar impact. Felipe Antonio Chegury Viana, who designed the Ant Colony Algorithm Based on Dynamic adjustable shock absorber. These methods have the power to design high cost of boring bar vibration, structural complexity, the maintenance of trouble, the current application is not widespread. The following will be used virtual prototyping technology in response to these problems. In the ADAMS environment damper structural optimization, and finally to carry out experiments. By comparing the analysis results show that the theory of optimization, simulation results and experimental results are basically the same, lower design cost. 2. Driving force for boring bar vibration theory and modeling Damping is the main driving force for the energy transfer system to the shock absorber system to reduce the vibration of the main system. Boring bar vibration structure as shown in Figure 1, the establishment of the mechanical model shown in Figure 2. Kinetic equation can be expressed as 1.the body of Boring Bar 2. rubber ring 3.gasket 4.damping block 5. damping 6.blocking 7.segment Fig.1 Boring bar vibration structure Fig.2the establishment of the mechanical mode The main system for the vibration amplitude For different values of the main system by the amplitude-frequency response curve as shown in Figure 3. Fig.3 different damping ratio of vibration amplitude-frequency characteristic curve When ξ = ∞, the boring bar and there is no relative motion between the shock absorber, a single degree of freedom system, when amplitude-frequency curve is only one peak, equivalent to an ordinary boring bar. When the range of ξ between 0 and ∞, the system of two degrees of freedom, resulting in the two resonance points. The existence of the damping of the resonance amplitude of the main system to reduce, but it does not completely eliminate the vibration of the main system. Figure 3 are all of the curves intersect at P, Q two points, indicating that P, Q two points and the frequency and amplitude changes in ξ has nothing to do, come to the equation for Calculated P, Q two points in the frequency Into (2) to be P, Q two points of the amplitude. From (2), (3) style can be seen that the main system for determining, the amplitude and frequency depend on the quality shock absorber and spring. Structural parameters of the best shock absorber should be in the P, Q two points to reach the peak, and the same values. According to this line of thought, according to the following steps to select the optimal parameters of shock absorber. For the determination of the main system and the selected block damping quality, the structure of the optimal solution for the parameters: To determine the stiffness of shock absorber In P, Q two points from stagnation conditions, the shock absorber damping rate obtained ξ 3. Dynamics Simulation In order to verify the validity of the model, ADAM S in the simulation environment. ADAMS application modules in the finite element model boring into flexible, in the head end of the creation of input and output channel, and then the vibration system analysis, through simulation, in the post-processing module to draw modal system and frequency response function. The initial parameters of shock absorber m2=0.02144，k2=10kN/m，c=10Ns/m。The size of boring structure: diameter D = 0. 016 m , length L =0. 192 m , aspect ratio of 12: 1. Material properties: density ρ = 7 801 kg / m, young's modulus E = 2. 07E + 011 N / m2, poisson's ratio ν = 0. 29. Damping block changes in the quality of the effects of amplitude-frequency curves.When m 2 = 0. 02 kg, the first two-order natural frequency of 253 Hz and 452 Hz, the maximum amplitude at resonance for the - 95. 16 dB and - 103. 3 dB;when m 2 = 0. 10 kg, order the first two natural frequency of 128 Hz and 406 Hz, the maximum amplitude at resonance for the - 95. 2 dB - 95. 3 dB. The quality of the different values of the main system mapping amplitude-frequency response curve shown in Figure 4. As can be seen as the natural frequency of vibration pieces to reduce the increase in quality, when the external excitation frequency and the main system close to the natural frequency, they can block the quality of vibration by modifying the way to avoid the occurrence of resonance, while the damping quality of the block not sensitive to the effects of amplitude. Amplitude/dBB Frequency/Hz Fig.4 With the quality of frequency response function curve Changes in damping characteristics of the amplitude-frequency curves. When c2 = 10 N s / m, the first two-order natural frequency of 253 Hz and 452 Hz, maximum amplitude of the resonance for the - 94. 75 dB and - 103. 24 dB; c2 = 2 N s / m, the first two bands of 253 Hz natural frequency and 452 Hz, maximum amplitude of the resonance for the - 90. 11 dB, and - 95. 49 dB. Figure 5 after the draw for the vibration analysis of the frequency response curve, indicating that changes in damping the impact of relatively large amplitude, the amplitude increases with decreasing damping, when the resonance unavoidable, by modifying the damping to reduce the amplitude, natural frequency and damping of the impact of less marked. Amplitude/dBB Frequency/Hz Fig.5 Frequency response function with the damping curve Changes in stiffness of the effects of amplitude-frequency characteristics. When the stiffness k2 = 10 kN / m, the first two natural frequency band 253 Hz and 452 Hz, the maximum amplitude at resonance for the - 94. 71 dB and - 108. 20 dB; When k2 = 200 kN / m, the first two natural frequency band 284 Hz and 898 Hz, the maximum amplitude at resonance for the - 90. 27 dB and - 110. 06 dB. Figure 6 The frequency response function for drawing maps showing the natural frequency with the increase of stiffness, rigidity of the impact of change on the relatively large amplitude, can be avoided by modifying the rigidity and adjusting the amplitude of resonance. Amplitude/dBB Frequency/Hz Fig.6 Frequency response function curve with the stiffness 4. Damping optimization Ordinary boring bar Damping according to driving force for boring bar vibration analysis model of shock absorber stiffness and damping as a design variable, the use of ADAMS and vibration in the View macro variables as the objective function, so that the smallest objective function. Constraints for the amplitude of vibration damper and the boring bar is less than the distance between the cavity and optimize the use of generalized OPTDES-GRG reduced gradient algorithm. The purpose of optimization is in a given structure and the boring bar vibration quality block under certain conditions, to optimize the stiffness of the damper and damping parameters, when using the optimal parameters of the main system when the minimum amplitude of vibration. When the quality of damping block m 2 = 0. 021 44 kg, the optimized curve and the general curve of boring bar shown in figure 7. Optimization of boring bar Amplitude/dBB Frequency/Hz Fig.7 Ordinary boring bar and boring bar vibration optimized Optimized the parameters of shock absorber is k2 = 58 662 N / m, c2 = 22. 34N s / m.Before the third-order natural frequency of 228 Hz, 309 Hz and 392 Hz, the first two bands of the ratio of the natural frequency of 0.7378. According to the formula (4) to calculate the natural frequency of the first two bands for the ratio of 0.7376, the relative error is 0.04%. Simulation and optimization of the damping rate of 0.221, the formula (6) derived from the damping rate of 0.216, the relative error is 2.2 percent. According to the quantitative analysis and theoretical simulation and optimization to optimize the results are basically the same, indicating that simulation optimization is effective and feasible. From Figure 7 can be seen in the excitation conditions remain unchanged, compared with the ordinary boring bar, boring bar vibration of the vibration mode has been marked improvement in vibration mode becomes more smooth, the amplitude is also significantly reduced. Maximum amplitude for the resonance - 102. 33 dB, based on signal processing theory, the actual amplitude and the amplitude of the correlation curve actual amplitude=10Magnitude/20 (7) M agnitude amplitude curve for the simulation, according to the real amplitude of type 0. 007 6 mm. General Boring Bar Boring Bar Vibration and Optimization of contrast in the table below that in the case of larger aspect ratio, power vibration amplitude vibration boring bar is just an ordinary boring bar of 23% amplitude, with very good damping effect . the results of comparative table ordinary boring bar and boring bar to optimize boring Bar vibration amplitude/dB actual value/mm natural frequency/Hz Aspect ratio General -89.88 0.0321 338 12:1 dynamic damping -102.33 0.0076 228.392 12:1 5. Conclusion In the dynamic simulation technology based on more dynamic system of boring bar vibration of the dynamic characteristics, as well as the shock absorber parameters change on the impact of the main system, and optimization of parameters, parameter optimization to optimize the results and theoretical results good, and finally through the scope and process. The method for further improving the level of deep processing and related areas of research have important theoretical and practical application value. References [1] D G Lee, H Y Hwang and J K Kim. Design and manufacture of acarbon fiber epoxy rotating boring bar [ J ]. Composite Structures,2003, 60 ( 1) : 115～124. [2] SANJ I G TEWAN I, KE ITH E ROUCH and BRUCE L WALCOTT A study of cutting p rocess stability of a boring bar with ac2tive dynam ic absorber [ J ]. I Mach. Tools Manufact 1995, 35 ( 1) : 91～108. [3] G B W arburton. Op tim um absorber parameters for m inim izing vibration response[ J ]. Journal of Earthquake Engineering and Structural Dynam ics , 1981, 9: 251～262. [4] J ia - Jang W u . Study on the inertia effect of helical sp ring of the absorber on suppressing the dynam ic responses of a beam subjected to a moving load [ J ]. Journal of Sound and V ibration. 2006, 297 ( 3- 5) : 981～999. [5] Felipe Antonio Chegury V iana, Giovanni Iam in Kotinda, Tuningdynam ic vibration absorbers by using ant colony op tim ization [ J ].Computers and Structures, 2008, 86 ( 13～14) : 1539～1549. 19