購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
目錄 1 緒 論 ......................................................................................................................................1 1.1 國內模具的現狀和發展趨勢 ...........................................1 1.1.1 國內模具的現狀 .................................................1 1.1.2 國內模具的發展趨勢 .............................................2 1.2 國外模具的現狀和發展趨勢 ...........................................3 1.3 限位板落料級進模具設計與制造方面 ...................................4 1.3.1 限位板沖孔落料級進模具設計的設計思路 ...........................4 1.3.2 限位板模具設計的進度 ...........................................4 2 沖壓件工藝分析 ......................................................................................................................5 3 工藝方案的確定 .....................................................................................................................7 3.1 方案的擬定 .....................................................................................................................7 3.2 方案比較 .........................................................................................................................7 3.3 方案選定 .........................................................................................................................7 4 必要的工藝計算 .....................................................................................................................8 4.1 排樣設計 .........................................................................................................................8 4.1.1 排樣方案擬定 ..........................................................................................................8 4.1.2 排樣方案比較 ..........................................................................................................8 4.1.3、方案選定 ..............................................................................................................11 4.2 計算凸、凹模工作部分的尺寸 ...................................................................................11 4.2.1 沖孔 30?凸、凹刃口尺寸的計算 ........................................................................11 4.2.2 外形落料凸、凹模刃口尺寸計算 ........................................................................12 4.3 沖壓力的計算 ...............................................................................................................13 4.3.1 沖孔力、落料力的計算 .........................................................................................13 4.3.2 沖孔、落料時的推件力、卸料力計算 .................................................................13 4.3.3 總的沖壓力計算： ................................................................................................14 4.4 壓力中心的計算 ...........................................................................................................14 5 模具的總體設計 ...................................................................................................................17 6 模具主要零部件的結構設計 ...............................................................................................19 6.1 凸模、凹模的結構設計 ...............................................................................................19 6.1.1 沖孔凸模的結構設計。 .........................................................................................19 6.1.2 落料凸模的結構設計 ............................................................................................19 6.1.3 凹模板的設計 ........................................................................................................21 6.1.4 導正銷的設計 ........................................................................................................21 6.1.5 固定擋料銷位置的確定 .........................................................................................22 6.1.6 導料板的設計 ........................................................................................................23 6.1.7 卸料板的設計 ........................................................................................................23 6.1.8 始用擋料銷位置確定 .............................................................................................23 6.2 模架的選擇 ...................................................................................................................24 6.3 模具的閉合高度 ............................................................................................................24 7 沖壓設備的選擇 ...................................................................................................................25 8 模具總裝圖的繪制 ...............................................................................................................26 9 設計總結 ...............................................................................................................................27 致 謝 .......................................................................................................................................28 參考文獻 ...................................................................................................................................29