3148 碼坯機升降機構設計,碼坯機,升降,機構,設計 碼坯機升降機構設計JIANGXI AGRICULTURAL UNIVERSITY本 科 畢 業 論 文（設 計）題目： 碼 坯 機 升 降 機 構 設 計 學 院： 工 學 院 姓 名： 蔚 延 年 學 號： 20080978 專 業： 機械設計制造及其自動化 年 級： 2008 級 指導教師： 曾一凡 職 稱： 副教授 二 0一二 年 五 月碼坯機升降機構設計摘要現在，碼坯機主要由切條機、切坯機、分坯機、夾盤機構、行走機構、升降機構、旋轉機構和電氣系統等組成。其中升降機構是其中一個重要部分，現在升降機構一般采用液壓升降與滾子鏈升降兩種方法。液壓升降因?yàn)橐簤涸闹圃炀纫筝^高、價格較貴，而且不能得到嚴格的傳動比、效率較低。又由于工作性能易受到溫度變化的影響，因此不宜在很高或很低的溫度條件下工作，所以設計采用滾子鏈升降。因?yàn)樾凶邫C(jī)構與升降機構一體，所以一起設計了。升降采用滾子鏈，使其運動準確，避免打滑現象，同時利用四個導向柱，增加設備的穩定性。滾子鏈由大小鏈輪帶動，共四組，布于四周，通過擺線針輪減速機通過齒輪箱帶動兩根軸實現同步上升。最后在車架兩端加上配重，通過鋼絲繩與夾盤機構連接，這樣可以減輕滾子鏈?zhǔn)芰?，減小功率。行走機構通過另一擺線針輪減速機帶動行走軸行走。此為本文設計方案，并且通過計算，論證了該設計方案的可行性。關鍵詞：碼坯機；升降機構；行走機構；滾子鏈升降碼坯機升降機構設計AbstractNow, setting machine is mainly composed of a cutting machine, cutting machine, cutter, chuck mechanism, running mechanism, lifting mechanism, a rotating mechanism and electrical system. The lifting mechanism is one of the most important parts, now lifting mechanism generally adopt hydraulic lifting and roller chain lifting two methods. Hydraulic lift for hydraulic components of the manufacturing precision is high, the price is more expensive, but can not be a strict transmission ratio, low efficiency. Because the working performance are susceptible to the influence of temperature change, therefore not at very high or very low temperature conditions, so the design of the roller chain lifting. Because the running mechanism and the lifting mechanism is integrated, so got together to design. Lifting the roller chain, the motion accuracy, avoid the slip phenomenon, at the same time using four guide posts, increases the stability of equipment. Roller chain sprocket drive by size, a total of four groups, the cloth around, through the cycloidal pinwheel speed reducer through the gear box drives two axis synchronous rise. In the final frame ends with counterweight, through the steel wire rope and the chuck body connected, this can reduce roller chain stress, reduce power. Walking mechanism through another cycloid reducer drive shaft walk walking. This is the design, and through calculation, it proves the feasibility of design scheme.Key words :Setting machine; lifting mechanism; running mechanism; the roller chain lifter