目錄摘 要 ---------------------------------------------------------------1第一章 緒論 -------------------------------------------------------31.1 選題的依據及課題意義 -----------------------------------------31.2 國內外滾齒機的研究發展?fàn)顩r -----------------------------------3第二章 滾齒機總體設計 -------------------------------------------62.1 滾齒機的工作原理 ---------------------------------------------62.2 滾齒機的結構設計 --------------------------------------------62.3 滾齒機的傳動方案設計 ----------------------------------------72.4 主傳動方案的評定與選擇 --------------------------------------102.5 電動機的選擇 ------------------------------------------------122.6 滾齒機的技術規格 --------------------------------------------13第三章 刀架結構設計 ---------------------------------------------143.1 滾刀刀架的結構介紹 ------------------------------------------143.2 刀架結構的設計計算 -----------------------------------------153.2.1 直齒輪的設計 ------------------------------------------153.2.2 滾刀心軸的結構設計 ------------------------------------18第四章 滾刀箱及其余部件設計 -----------------------------------214.1 滾刀箱的設計 ------------------------------------------------214.2 滾刀牙箱設計 -----------------------------------------------234.3 刀架立柱設計 -----------------------------------------------23總 結 -----------------------------------------------------------24參考文獻 -----------------------------------------------------------25致 謝 -----------------------------------------------------------26附錄一 -------------------------------------------------------------27附錄二 -------------------------------------------------------------330Y3150E 型滾齒機刀架設計摘 要滾齒機是齒輪滾刀加工齒輪的專用機床，在齒輪加工中應用最廣泛。在滾齒機上可切削直齒、斜齒圓柱齒輪。這種機床使用特制的滾刀時也能加工渦輪、花鍵和鏈輪等各種特殊齒形的工件。本滾齒機由床身、立柱、刀架及滑板、工作臺組成。滾刀箱固定在刀架滑板上，滾刀心軸插入滾刀主軸并用拉緊螺栓固定在主軸上。為了保證主軸與前軸承的適當間隙，前軸承是做成外錐并開口。調整軸承上的兩個螺母，可以使前軸承做軸向移動，使前軸承孔收縮便可消除主軸和軸承間過大的間隙。我的課題主要內容是滾齒機刀架系統設計：以 8mm 最大加工模數為基本參數，對滾齒機刀架進行設計，擬定總體方案，進行結構設計，對主要的零件進行設計計算和強度校核。使設計的刀架可用于齒輪加工，最后用 CAD 軟件生成圖紙。關鍵詞：滾齒機、刀架、齒輪1Y3150E Gear Hobbing Machine Cutter Frame DesignAbstractThe gear hobbing machine is special purpose machine tools cutting gear with gear hob and it is widely used.It can be used for machining spur cylindrical gears,helical cylindrical gears.With special hobbing cutter,it could machine worm gears multiple spline and sprocket wheels whose tooth profile are special.This gear hobbing machine is composed of bed,column,cutter frame,slider,and machine table.Rob cutter frame is fixed on the slide of cutter rack, the hob shaft is inserted into hob spindle and fixed with the draw-in bolt on the main axle. In order to guarantee the spindle and the suitable front bearing gap, the front bearing has the outer cone and the aperture. Adjusting on the bearing two nuts, it causes bearing movement along the front axle when motion and causes contraction of the front bearing hole then to be possible to eliminate the gap between the main axle and the bearing. The topic main content of topic is hob-cutter frame design as well as the spindle assembly design:8mm maximum machining modulus of the basic parameters,hobbing tool holder to design,develop the overall program,structural design,the main parts of the design calculation and strength check.Make the design of the turret and the table can be used for gear cutting,finally with CAD software to generate drawings.Key words :gear hobbing machine,cutter frame, gear