購買設(shè)計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預(yù)覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。有不明白之處，可咨詢QQ:1304139763

Ming Cong and Bo Fang School of Mechanical Engineering Dalian University of Technology Dalian 116024 China congm This work is supported by national natural science fund 50675027to Ming Cong Abstract This paper presents a multisensor system for combining measurements from ultrasonic sensors and navigation for robot mowers The proposed sensing system enables robot mowers to mapping unknown environments It is important for an autonomous robot mower to explore its surroundings in performing the task of localization and navigation for mowing Because of the complexity of the environment one simple kind of sensors is not sufficient for robot mower to accomplish these tasks We develop a robot mower equipped with DSP TMS320F2812 as its CPU The sensing system integrates with ultrasonic sensors infrared sensors collision sensors encoders a temperature sensor and an electronic compass A method of high accuracy ultrasonic ranging technology based on wavelet transform is reported to improve the measurement precision of ultrasonic sensors Simulation studies show that the proposed multisensor fusion method is very effective for the navigation of robot mowers Experimental results indicate that this sensing system based on generalized auto correlation method for obstacle detection and localization shows great potential for providing a high performance to price ratio and robust solution for robot mowers in dynamic working condition Index Terms multisensor fusion ultrasonic sensors robot mower mapping navigation I INTRODUCTION Lawn mowing is considered by many to be one of the most boring and tiring routine tasks The environmental robots are needed urgently to perform the task Some predictions indicate that the robot mowers will be one of the most promising personal robot applications and have substantial market in the world Therefore the concept of Intelligent Robot Mower IRM had been proposed for the first time in 1997 s annual conference of the OPEI Outdoor Power Equipment Institute 1 The robots mainly face to the general families to help the busy people and the hypodynamic old folks save the payments for hiring labours also remove people from noise pollen and danger of mowing blade The robot mowers serve for home care as the outdoor mobile robots actually kind of intelligent mechatronics devices for environment clean up 2 3 The important thing is that the robot mowers are representative of some area covering environmental robots used not only for indoor floor cleaning as in 4 but also in hazardous environments such as removing landmines cleaning up radiant points and prospecting for resources etc The robot mowers get great challenges differing from indoor mobile robots The robot mowers use sensors to understand environments as well as their real time states for obstacle avoidance map building location and navigation in the whole work area Because of the complexity of the environment one simple kind of sensors is not sufficient for robot mower to accomplish these tasks It is necessary to combine the observed sensor data coming from different sensors to reduce the uncertainties of the robot in any working environment To merge the information from the various sensors robust and real time sensor fusion is required 5 In cases of sensor error or failure multisensor fusion can also reduce uncertainty in the information and increase its reliability A sensing system of low cost low power consumption high performance is described The detecting range of ultrasonic sensors is 0 3m 5m they provide good range information However uncertainties in ultrasonic sensors caused by the specular reflection from environments make them less attractive The detecting range of infrared sensors is 0 02m 1m they can detect the obstacles within the ultrasonic sensor s blind zone In order to satisfy the needs of robot mowers for the low cost and high accuracy ranging technology the research on the high accuracy ultrasonic ranging technology based on wavelet transform WT is reported to improve the measurement precision of ultrasonic sensors Measurement data gathered from the sensing system are integrated to avoid the robot mower from unknown obstacles and plan an optimum reliable and realizable plan completely coverage of entire working area Finally simulation studies and experimental results show the effectiveness of the sensing system for the navigation obstacle detection and localization of robot mowers II SYSTEM HARDWARE OF IRM The IRM uses DSP TMS320F2812 as its CPU including four units vehicle system cutting system sensing system and control system The sensing system is used to collect the external dynamic information of the working environment for obstacle avoidance map building navigation and localization It is also used to detect vehicle system s movement parameters and cutting mechanism s working status The controller compares the acquired information with the database and then sends out revisory and accurate command to the robot to perform its tasks The hardware of the IRM is shown in Fig 1 Multisensor Fusion and Navigation for Robot Mower 978 1 4244 1758 2 08 25 00 2008 IEEE 417 Proceedings of the 2007 IEEE International Conference on Robotics and Biomimetics December 15 18 2007 Sanya China Fig 1 Hardware overview of IMR The robot must be physically strong computationally fast behaviourally accurate and safety It should have the ability to perform on its own and required no human intervention during the whole or most part of the mowing period The IRM is modularized designed and each unit of the IRM is relatively independent Modularized design makes the maintenance much easier Any broken unit of the IRM can be replaced directly without influencing the functions of other units III SENSING SYSTEM A Ultrasonic Sensor Unit Because ultrasonic sensors can provide good range information based on the time of the flight TOF principle mainly due to their simplicity and relatively low cost they have been widely used in mobile robots for obstacle avoidance map building and so on This type of external sensor is very good in obstacles distance measurement The main lobe of the sensitivity function is contained within an angle of 20 degrees as shown in Fig 2 6 A number of tests showed that the range accuracy of the sensors is in the order of 2cm Fig 2 Typical intensity distribution of an ultrasonic sensor On IRM we set up a sensor array which consists of 12 ultrasonic sensors spaced 30 degrees apart The ultrasonic signals can cover all the space around and satisfy the space requirement about which robot can detect the environmental signals Classical techniques used in ultrasonic transducers are based on TOF measurement which calculates the distance of the nearest reflector using the speed of sound in air and the emitted pulse and echo arrival times The distance d to a reflected object is calculated by 2dct 1 where c is the speed of sound and t is the time of flight The TOF method produces a range value when the echo amplitude first exceeds the threshold level after transmitting ignoring a second echo from a further reflector The ultrasonic sensor unit includes a trigger pulse generation unit a multi channel selection unit and an echo receiving unit A sensor interface circuitry designed to send and receive ultrasonic sound pulses catches always the first returning echo The range data related to an object is considered to be on the conic axes even if it is located off the axes The ultrasonic wave typically has a frequency between 40 and 180 kHz and the frequency of the ultrasonic sensors used in the system is 40 kHz The beam angle is 20 degrees The 40 kHz PWM pulse is generated by the general purpose timer unit of DSP To drive the transmitter effectively and not to bring much vibration an 8 cycle burst of ultrasound at 40 kHz is sent out once a time When the ultrasonic pulse is emitted the sensor will experience ringing Ringing caused by the transmitted pulse can cause the receiver to detect a false echo This problem is solved by not enabling the capture interrupt of DSP until a delay interval has passed This means that the ranger can not detect an object whose distance from the sensor is less than half the distance that sound travels during the delay interval This is the blind zone of the ultrasonic sensor as shown in Fig 3 Trigger pulse Emitted signal Received signal TOF Blind zone Echo Fig 3 The sketch map of ultrasonic transmission and reception B Infrared Sensor Unit and Other Sensors To overcome the ultrasonic sensor s blind zone infrared sensors are added The infrared sensors can detect obstacles within 20cm which patch up the problem caused by the blind zone problem of ultrasonic sensors This unit has 16 infrared sensors Each infrared range finder has a conic view of 6 degrees which is the main lobe of the sensitivity function This sensor has a useful measuring range of a target up to about one meter with high accuracy A number of tests showed that the range accuracy of the sensors is in the order of lcm In order to save the DSP s resource 16 infrared sensors are connected with DSP TMS320F2812 s data interface 418 instead of the IO interface This kind of architecture can also read the sensors status at the same time ensuring the real time capability of the system A sensor interface circuitry designed to send and receive infrared pulses catches always the first retuning echo to process its amplitude Robot mower works in an outdoor environment where the temperature changes rapidly The changing of temperature will affect the speed of sound Therefore a temperature sensor is used to guarantee the precision of the ultrasonic sensor Collision sensor is a group of sensitive swatches which used to prevent the damage caused by unexpected collision Because moist environment do harm to the circuit of the IRM humidity sensors are introduced to detect the humidity of the environment Although these sensors are not absolutely necessary for an autonomous robot mower they can provide helpful functions to make the work availability and safety IV SENSOR BASED NAVIGATION A Mapping As seen in Fig 4 a reference direction x is defined and the robot coordinates are shown as R x R y By the help of an electronic compass built in on the robot 7 the angle i which is the ith sensor s angle from the 1st sensor can be easily measured Actually if only the angle S heading angle of the robot is measured other sensor angles can be found as iSi 2 where i is the angle to the our world coordinate center The number of maximum sensor group on the ultrasonic ring is n and the radius is r in our system n 12 and r 0 25m The distance between the origin and the center of the ring is R and reference angle to the center is The reference position of the robot s center is R x R y The distance from the origin to object which is detected by the ith sensor data on the two dimensional plane is called i R Now let i dm denote measured value which is combined data from the ultrasonic and infrared sensors for the exact distance i R There will be an error i between these values as iii dm d 3 In this work we naturally assume that i is a uniform random variable in the range of W W Here W denotes the maximum distance measurement error Here the problem is given R x R y r 12 n g34 and 12 n dm dm dmg34 to estimate the coordinates of the occupied cells i x and i y or equivalently i R in most efficient way The equations involving the detected object can be written as 222 cos sin iR i i R i i Rxrd yrd 4 22 2 2 cos sin iii RR rd rdx y 22 2 2 cos ii R R R rd rd 5 y x x y R R g455 d d O Fig 4 The robot position on x y section The equations involving the robot due to the object can be written as 222 cos sin iiii i Rxrd yrd 6 222 2 2 cos sin ii i ii ii i Rxy rd rdx y If we define the positions as 11 TT in Ppp p xy g34 then we have 22 2 2 cos sin ii ii ii R R rd rd y P 7 After the inserting the 2 i R in 2 R cos cos sin iiii rd R y P 8 Here again we have n such equations And we write them in matrix form i mAP 9 And if we introduce new matrix as cos sin iiii LP and 0 0 then 10 can be written as 111 1 2 cos cos R nRn nn rdm R L p L rdm R L p g170g186g170 g186g170g186 g171g187g171 g187g171g187 g171g187g171 g187g171g187 g171g187g171 g187g171g187 g171g187g171 g187g171g187 g171g187g171 g187g171g187 g171g187g171 g187g171g187 g172g188g172 g188g172g188 Here if we perform the least squares estimate for i P we obtain 1 TT lsq i PAAAm 11 Thus we find the best squares estimate of the positions B Simulation Studies Sensor based navigation has been tested with simulation to shown the usefulness of this sensor fusion method in the two environments respectively as shown in Fig 5 and Fig 6 The mower has been primarily tested in a structured laboratory as shown in Fig 5 Start at 0 3m 0 5m 0degree a virtual 419 robot was driven around a virtual square corridor one time The walls in the artificial environment are denoted by the real map The entire vehicle is self contained It has a maximum travel speed on 0 4 m s The laboratory area was surveyed out to a 10cm grid with accuracy better than about 1cm To extract the mapping a start and goal points were presented The robot position and orientation were established by the electronic compass 8 Fig 5 Data collection and navigation result in structured environment The result in Fig 5 demonstrates the mapping quality and the usefulness of this sensor fusion method In the tests we find that the average error in estimating the position of the obstacles in the environment was in the range of 0 2 0 2 m In the simulations we see that lsq i P in 11 obtained does not satisfy ilsqi RP which actually should In the case a better estimate for the positions can be given as i ei lsqi lsq i R PP P 12 In this case estimate for the angle i does not change but the estimate for distance i R is scaled to it best estimate Therefore for the position the distance estimate i R remains the same as before while the least squares estimate works only for the angle i Simulations show that this way produces more accurate results Fig 6 The simulation result of wall following behavior Wall following was selected for the initial problem domain because it is a fairly simple problem to set up and evaluate 9 It also lays the groundwork for more complex problem domains such as maze traversal mapping and complete coverage path planning which is used on lawn mowing and vacuuming The simulation result of wall following behavior shown in Fig 6 and the experimental result in Fig 6 demonstrate that the IRM have the capability to perform its mowing task in unstructured environment The program of sensor based navigation simulation in Fig 5 is given below Sub Main Dim PI Fcr Fct X target Y target X Y As Single Dim X grid Y grid i j C As Integer Dim Frx Fry d dist targ rot Fx Fy As Single Dim Fcx Fcy Rx Ry As Single PI 3 1415927 Fcr 1 Fct 1 X target GetMarkX 0 Y target GetMarkY 0 SetCellSize 0 0 1 Set cell size 10 cm x 10 cm SetTimeStep 0 1 Set simulation time step of 0 1 seconds Do Start main loop X GetMobotX 0 Present mobot coordinates in meters Y GetMobotY 0 X grid CoordToGrid 0 X indexes of cells where the Y grid CoordToGrid 0 Y mobot center is MeasureRange 0 1 3 Perform a range scan and update the Certainty Grid max cell value 3 Frx 0 Fry 0 Each ocuppied cell inside the windows of 33 x 33 cells applies a repulsive force to the mobot For i X grid 16 To X grid 16 For j Y grid 16 To Y grid 16 C GetCell 0 i j If C 0 Then d Sqr X grid i 2 Y grid j 2 If d 0 Then Frx Frx Fcr C d 2 X grid i d Fry Fry Fcr C d 2 Y grid j d End If End If Next Next dist targ Sqr X X target 2 Y Y target 2 Fcx Fct X target X dist targ Fcy Fct Y target Y dist targ Rx Frx Fcx Ry Fry Fcy rot RotationalDiff 0 X Rx Y Ry shortest rotational difference between current direction of travel and direction of vector R SetSteering 0 0 5 3 rot mobot turns into the direction of R at constant speed and steering rate proportional to the rotational difference StepForward Loop Until dist targ 0 1 Loop until mobot reaches the target End Sub 420 V ULTRASONIC RANGING TECHNOLOGY BASED ON WT Unfortunately the practical received multi echoes has time varying property and is a typical non stationary signal because the influence of the environmental complexity and the noise Furthermore the noise mixed in the ultrasonic pulse echo is Non Gaussian white noise but colored noise and correlated with the target echo The TOF method can not be used directly in such conditions Referencing the generalized correlation method for estimation of time delay 10 we put forward the generalized auto correlation method for estimation of time of flight based on wavelet transform 11 and present in Fig 7 Fig 7 Delay estimation of generalized auto correlation based on WT Where t is the mother wavelet and a t is the daughter wavelet The coefficient is the scale or scaling factor and is the time displacement The wavelet transform of the signal x t is yt Actually this is a filtering process of the ultrasonic echo using a multitude of bandpass filters of equal Q which is equivalent to the whitening filter of the generalized correlation method for estimation of time delay in order to eliminate the input noise which can influence the following processing yy R can be found as yy xx a a R Eyt yt R t t t As there has the relationship of Fourier transform between auto correlation function yy R and his power spectrume 2 yy yy xx xx GFRG aaG a We obtain the generalized auto correlation function as Last the peak values of yy R are detected to accomplish the estimation of TOF and calculate the real ultrasonic velocity Fig 8 Noisy ultrasonic echo Fig 9 Denoised echo using WT Fig 10 Auto correlation function yy R Fig 11 Peak detection The noisy ultrasonic echo is shown in Fig 8 and the denoised ultrasonic echo by wavelet transform is shown in Fig 9 It is obvious that the noise mixed in the ultrasonic echo is effectively eliminated after WT operation The auto correlation operation yy R of the denoised ultrasonic echo is shown in Fig 10 Fig 11 shows the envelope of yy R through Hilbert transform As we can see if the abscissa of every peak point is determined the estimation of TOF g109 ND can be calculated Considered the attenuation of the ultrasonic echo and the demand of the high precision in practice only the former four echoes are used to estimate the TOF The values of the TOF estimation are g110g110 g109 g108 g109 g109 3 2 2 3DDDDDD which are symmetrical to the x axis Using this method the estimation of the ultrasonic velocity can be calculated So far an obstacle detection and localization system has been implemented successfully By means of above method an obstacle detection and localization system has been implemented successfully The generalized auto correlation method based on wavelet transform is put forward to realize the real time ultrasonic velocity measurement and this method can 11 22 gj j yy yy g yy RG Ged g179g179 421 eliminate the influence of temperature humidity and wind on ultrasonic velocity measurements when the robots are working in dynamic condition And this sensing system based on generalized auto correlation method shows great potential for providing a robust solution for robot mowers in dynamic working condition VI EXPERIMENTAL RESULTS We measure the distance between the robot and plane objects using the ultrasonic sensors The measured results and the actual distances are shown in TABLE I TABLE I THE EXPERIMENTAL DATA OF THE ULTRASONIC SENSORS unit cm Actual distance Measured value1 Measured value2 Average error 30 30 62 30 61 2 50 40 40 70 41 69 1 73 50 50 64 50 67 1 31 60 60 73 60 73 1 22 70 70 81 70 84 1 19 80 81 09 81 04 1 33 90 91 10 91 13 1 24 100 98 82 99 15 1 02 150 148 24 148 37 1 13 200 201 85 201 85 0 93 250 252 71 252 74 1 09 300 302 52 302 58 0 85 350 347 63 347 61 0 68 400 405 75 405 77 1 44 450 456 22 456 26 1 39 500 508 87 508 90 1 77 From TABLE I we can see that the measurement error of the ultrasonic senso